DO
GUIDE
DO
Check the Box
QUANTITY
PRODUCT
COLOR
PART NUMBER
1
Bit, Torx, T8
2025915
4
Screw, 6-32 x 3/4", Undercut Head, Phillips
2033247
4
Screw, M3 x 16 mm, Flat Head, Phillips
2013788
4
Screw, 4-40 x 3/4", Pan Head, Phillips
2007184
2
Screw, M3.5 x 25 mm, Flat Head, Phillips
2023756
Items for IDOC-PAD-LCA-DSWC-B-S and IDOC-PAD-LCA2-DSWC-B-S
1
Cover, Front
Black
4519812
1
Plate, Mounting
Black
2040499
2
Screw, 2-56 x 5/16", Pan Head, Torx
Black
2040263
4
Screw, 6-32 x 1/4", Pan Head, Phillips
Black
2007215
Items for IDOC-PAD-LCA-DSWC-W-S and IDOC-PAD-LCA2-DSWC-W-S
1
Cover, Front
White
4519811
1
Plate, Mounting
White
2039781
2
Screw, 2-56 x 5/16", Pan Head, Torx
2040264
4
Screw, 6-32 x 1/4", Pan Head, Phillips
2007213
2. Connect the 24 Vdc or PoE line and earth ground to the rear of the iPanel.
NOTE
: Ensure the unit is properly grounded by connecting the chassis ground terminal to an earth ground (building steel). If PoE is used, an earth
ground connection must still be made to the terminal block connector.
NOTE
: The iPanel can be connected to 24 Vdc and and PoE simultaneously.
3. Lift and remove the plastic cover from the iPanel.
4. Use the Phillips screwdriver to remove the screws and washers that hold the metal plate in place, and remove the metal plate.
NOTE
: If necessary, remove the cable holder.
IDOC-PAD-LCA(2)-DSWC
iPanel
®
Wall Dock for iPad Air
®
Devices
DO
Install the Device
The Crestron
®
IDOC-PAD-LCA-DSWC and IDOC-PAD-LCA2-DSWC iPanel
®
Wall Docks feature similar operation. For simplicity within this guide, the
term “iPanel” is used except where noted. Similarly, the word “iPad” is used to denote iPad Air and iPad Air
2. The iPad
®
is sold separately.
For the iPad Air, use the IDOC-PAD-LCA-DSWC. For the iPad Air 2, use the IDOC-PAD-LCA2-DSWC.
The Crestron iPanel installs into a standard 2-gang U.S., U.K., or European electrical box. It can also be attached directly to drywall and other surfaces
over the front of a 2-3/8" H x 3-3/8" W (60 mm H x 86 mm W) cutout. When installed, it protrudes just 1" (26 mm) from the mounting surface and secures
to its included mounting plate with included screws.
Choose a Location
To allow installation and removal of the iPad, the iPanel requires a minimum amount of clearance on both sides. When choosing an installation location,
make sure the center of the mounting location has a minimum of 7-7/16" (189 mm) clearance on the closed side of the iPanel and 15-1/2" (394 mm)
clearance on the open side of the iPanel, as shown below.
NOTE
: Although the iPanel can be mounted with the opening oriented to the right, note that the iPad Air volume buttons face downward in this
configuration. This may not be optimal for the end user.
Required Tools
The following are required to install the iPanel.
• #2 Phillips screwdriver
• Torx bit (included) and driver (not included)
Install the Device into an Electrical Box
NOTE
: A 24 Vdc or PoE cable should already be in the electrical box. The iPanel can use only one source for power.
1. Use the included screws to attach the mounting plate to the electrical box.
• For U.S.-style installations, use the included 06-32 x 3/4" screws.
• For U.K.-style installations, use the included 3.5 x 25 mm screws.
• For European-style installations, use the included 3 x 16 mm screws.
24 Vdc
PoE
24
G
Lift here.
Remove
screws and
washers.
Minimum Wall Distance
Minimum Wall Distance
2 in
(51 mm)
2 in
(51 mm)
15-1/2 in
(394 mm)
7-7/16 in
(189 mm)
Center Box Cutout
U.S. Electrical Box
Mounting Plate
Screws (4) 6-32 X 3/4"
Screws (2) 3.5 X 25 mm
U.K. Electrical Box
Mounting Plate
European
Electrical Box
Mounting Plate
Screws (4) 3 X 16 mm
