manualshive.com logo in svg

Crestron Green Light DIN-1DIM4, Operations & Installation Manual, Page: 32 / 36

Share
Download
Crestron Green Light DIN-1DIM4 Operations & Installation Manual Download Page 32

DIN Rail 4-Channel Dimmer 

 

Crestron 

DIN-1DIM4 

NOTE:

  All Crestron certified Cresnet wiring must consist of two 

twisted pairs. One twisted pair is the +24V conductor and the GND 
conductor and the other twisted pair is the Y conductor and the Z 
conductor.  

Strip and Tin 
Wire 

When daisy-chaining Cresnet units, strip the ends of the wires carefully 
to avoid nicking the conductors. Twist together the ends of the wires that 
share a pin on the network connector and tin the twisted connection. 
Apply solder only to the ends of the twisted wires. Avoid tinning too far 
up the wires or the end becomes brittle. Insert the tinned connection into 
the Cresnet connector and tighten the retaining screw. Repeat the 
procedure for the other three conductors. 

Add Hubs

 

Use of a Cresnet Hub/Repeater (CNXHUB) is advised whenever the 
number of Cresnet devices on a network exceeds 20 or when the 
combined total length of Cresnet cable exceeds 914 meters (3000 feet). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

28  

•

  DIN Rail 4-Channel Dimmer: DIN-1DIM4  Operations & Installation Guide – DOC. 6928A 

Summary of Contents for Green Light DIN-1DIM4





































Reviews:

No comments