manualshive.com logo in svg

Crestron C2N-FTB, Operations & Installation Manual

Share
Download
Crestron C2N-FTB Operations & Installation Manual Download Page 3

Crestron 

C2N-FTB

  

 

FlipTop Control Center with Cresnet

®

 

Contents 

 

FlipTop Control Center  with Cresnet

®

: C2N-FTB 

1

 

Introduction ..........................................................................................................1

 

Features and Functions...........................................................................1

 

Specifications .........................................................................................2

 

Physical Description...............................................................................3

 

Industry Compliance ..............................................................................6

 

Setup.....................................................................................................................6

 

Network Wiring .....................................................................................6

 

Identity Code..........................................................................................8

 

Installation............................................................................................10

 

Hardware Hookup ................................................................................15

 

Ground Wire Connections....................................................................16

 

Configuration Software ......................................................................................17

 

Earliest Version Software Requirements for the PC ............................17

 

Configuring with Crestron SystemBuilder...........................................18

 

Configuring with SIMPL Windows .....................................................18

 

Example Program.................................................................................22

 

Uploading and Upgrading ..................................................................................23

 

Communication Settings ......................................................................23

 

Uploading a SIMPL Windows Program ..............................................25

 

Firmware Upgrade ...............................................................................27

 

Problem Solving .................................................................................................29

 

Further Inquiries...................................................................................29

 

Future Updates .....................................................................................29

 

Return and Warranty Policies.............................................................................30

 

Merchandise Returns / Repair Service .................................................30

 

CRESTRON Limited Warranty ...........................................................30

 

 

 
 
 
 
 

 

 
 
 
 

Operations & Installation Guide – DOC. 6338  

Contents 

•

 i

 

Summary of Contents for C2N-FTB





































Reviews:

No comments

Brands by name

Popular brands

Load more brands