manualshive.com logo in svg

Crestron C2N-FTB, Operations & Installation Manual

Share
Download
Crestron C2N-FTB Operations & Installation Manual Download Page 20

FlipTop Control Center with Cresnet

®

  

Crestron 

C2N-FTB

 

Consideration must be given if installed in a closed or multi-unit rack assembly, 
inside a closed desk, or in a closed podium since the operating ambient 
temperature of these environments may be greater than the room ambient. 
Contact with thermal insulating materials should be avoided on all sides of the 
unit. 

NOTE:

  The maximum continuous current from equipment under any external 

load conditions shall not exceed a current limit that is suitable for the minimum 
wire gauge used in interconnecting cables. The ratings on the connecting unit's 
supply input should be considered to prevent overloading the wiring. 

Underside Connections 

 

Ground Wire Connections 

Proper grounding is required. Connect the ground from the C2N-FTB to earth 
ground. Connect the Cresnet shield lead at the control processor to the ground 
lead. The control processor chassis must also be connected to an earth ground 
(building steel). Refer to the following grounding diagram. 

Ground Wire Connections 

 

NOTE:

 Do not connect the shield to earth ground at the C2N-FTB 

16 

•

 FlipTop Control Center with Cresnet

®

: C2N-FTB  Operations & Installation Guide - DOC. 6338 

Summary of Contents for C2N-FTB





































Reviews:

No comments

Brands by name

Popular brands

Load more brands