5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: 440/350-7267
www.crescor.com
© Crescent Metal Products, Inc. 2002 All rights reserved
Litho in U.S.A.
CRES COR
PAN
DIM “A”
DIM “B”
DIM “C”
INSIDE DIMENSIONS
WEIGHT
MODEL NO.
CAP/ANGLES
SIZE
WIDTH
DEPTH
HEIGHT
WIDTH
DEPTH
HEIGHT
ACT.
6
SEE NOTE
IN
28-3/4
37-3/4
43-3/4
21-1/4
26-1/2
28
LBS
296
CO-151-HUA-6B
SETS
BELOW
MM
740
960
1115
540
675
715
KG
134
Note: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
®
CO-151-HUA-6B
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
SHORT FORM SPECIFICATIONS
Cres Cor Roast-N-Hold Half Size Convection Oven
Model CO-151-HUA-6B. Removable power unit 20 ga.
304 stainless steel, recessed control panel. Cabinet and
door 22 ga. 304 stainless steel; stainless steel internal
frame; coved corner interior. Fiberglass insulation in
sides 2”; back, door and base 1-1/2”. High temperature
magnetic latch. (6) sets universal angles for multiple
pan sizes and spacing. One piece base .125 aluminum.
5" swivel modulus casters, Delrin bearings. Load
capacity 250 lbs. each. 4700 Watts,
Volts,
60 Hz.,
Phase. 2 year parts warranty. Provide
the following accessories:
_
.
UL Sanitation, UL, CUL listed.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23 at 75˚F.
•
1-1/2" in back wall, door, base; 2” in side walls.
• Air tunnel: 20 ga. stainless steel, lift-out type; mounted
•
on rear wall.
• Work Top: 18 ga., 304 stainless steel.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
•
250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DOOR:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latch: Chrome plated steel, high temperature ceramic
•
magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated steel, lift-off type; mounted
•
inboard.
• Gasket: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Wire angles (.306 dia.), nickel chrome plated; mounted on
lift-out posts.
• (6) sets of angles adjustable on 1-1/2" centers.
• Grids (3): Nickel chrome plated steel, raised wire 17” x 25”.
POWER REQUIREMENTS AVAILABLE:
• 4700 Watts, 208 Volts, 60 Hz., 1 phase, 24 Amps.,
•
30 Amp. service.
• 4700 Watts, 240 Volts, 60 Hz., 1 phase, 20 Amps.,
•
30 Amp. service.
• 4700 Watts, 208 Volts, 60 Hz., 3 phase, 13 Amps.,
•
20 Amp. service.
• 4700 Watts, 240 Volts, 60 Hz., 3 phase, 12 Amps.,
•
20 Amp. service.
POWER UNIT COMPONENTS:
(refer to above drawing)
• Body: Formed 20 ga. 304 stainless steel with black control
•
panel, recessed and tilted 7˚.
A) Thermostat (holding): Solid state, room ambient to 250˚F. (121˚C.).
B) Thermostat (cook/retherm): Solid state, room ambient to 350˚F.
B)
(176.5˚C.).
C) Pilot lights (2).
D) Switch: Lighted ON-OFF rocker type.
E) Timer: 24 hr. digital countdown; infinite memory retention.
F) Thermometer.
• Power cord: Permanent, 6 ft., 10/3 ga. with right angle plug.
• Heaters (3): 1470 Watts each.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 Amp.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
DETAIL OF
PAN SLIDE
6-30P
L15-20P
