Creek Audio VOYAGE i20 Instruction Manual Download Page 7

ENGLISH

ENGLISH

6

Auto Standby MENU options also allow for 30 mins, 1 hour, 2 hours or OFF.

REMOTE CONTROL
The Remote-control handset operation should be self-explanatory, but some functions require more explanation. 
The blue speaker Mute button at the top has two functions. Press the button once briefly to Mute or un-mute the output. Press and hold the 
MUTE button for two seconds to wake-up the amplifier from Standby or enter Standby mode.
 
The blue Volume up/down buttons on the right side of the remote adjust the level and the blue L or R buttons in the middle to adjust the balance. 
As the remote can manage more than one product, it may be necessary to press the blue AMP button at the top first if you have previously used 
the remote handset to control an action on the Voyage CD.

DISPLAY
An OLED graphical display in the centre of the front panel indicates the status of the amplifier. 
When initially powering up, the CREEK logo will be displayed for a few seconds. Only during this period is the SETUP MENU available. See SETUP 
paragraph for more information. The amplifier is ready for use once the display changes to show selected input and volume setting. There will be 
a click from internal relays selecting the chosen input and output relay un-muting.

ANALOGUE INPUT CONNECTIONS
Inputs 1, 2, and 3 provide inputs for most unbalanced* analogue audio signals.

Input 1    

Line level input via RCA sockets, with a signal sensitivity of approximately 650mV for full power. Unlike the other line inputs,  

 

 

Line 1 can also be configured as a Phono input by installing a Sequel mk4 Phono pre-amp. 

Input 2   

Line level input via gold RCA sockets.

Input 3   

Line level input via gold RCA sockets.

  

 

The red marker indicates the right channel and white indicates the left channel.

Input 4    

Line level input via XLR plugs. Balanced audio*

 

 

Right and Left channel is printed above each of the XLR sockets.

Sequel mk4 

This optional Moving Magnet (MM) Phono pre-amplifier plugs into the pre-amplifier section of the Voyage i20, replacing a Link  

 

 

PCB. 

Summary of Contents for VOYAGE i20



















Reviews: