CR24 UPKIT
3
Made in USA
LPN000131_A
www.cree.com/lighting
CREE
®
TRUEWHITE
®
TECHNOLOGY FIXTURE LIMITED CONSUMER WARRANTY
The limited warranty set forth below is given by the Cree company listed below ("Seller") with respect to the lighting product packaged with this limited warranty (the "Product"). Your Product, when delivered to you in new condition in
its original packaging, is warranted against defects in materials or workmanship as follows: for a period of FIVE (5) YEARS from the date of original purchase, defective parts or a defective Product returned with the sales receipt as
proof of purchase to Seller, or its authorized service providers, as applicable, and proven to be defective upon inspection, will be repaired, or exchanged for a new Product, as determined by Seller, or the authorized service provider.
This limited warranty covers all defects encountered in normal use of the Product, and does not apply in the following cases: Loss of or damage to the Product due to acts of God; fire; vandalism; civil disturbances; power surges;
improper power supply; electrical current fluctuations; corrosive environment installations; induced vibration; harmonic oscillation or resonance associated with movement of air currents around the product; abuse; alteration; accident;
mishandling; failure to follow operating, maintenance or environmental instructions prescribed by Seller in writing or services performed by someone other than Seller or its authorized service provider. WARRANTY IS VOID IF
PRODUCT IS NOT USED FOR THE PURPOSE FOR WHICH THIS PRODUCT IS MANUFACTURED. Any complaints you may have regarding the Product should be addressed to Ruud Lighting, Inc., 9201 Washington Avenue,
Racine, WI 53406. Seller shall have no liability under this warranty unless Seller is notified in writing within sixty (60) days after your discovery of the defect and the defective items are promptly returned to Seller, freight prepaid, and
received by Seller. This warranty excludes field labor and service charges related to the repair or replacement of the product.
NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, APPLIES TO THE PRODUCT AFTER THE APPLICABLE PERIOD OF THE
EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE PRODUCT SHALL BIND SELLER. (SOME
STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.)
LIGHT ENGINE
MAIN POWER
WHITE - NEUTRAL
SIDE PANEL
SIDE PANEL
BLACK #1 - HOT
BLACK #2 - HOT (OPTIONAL)
GREEN OR BARE WIRE - GROUND
DIMMING SUPPLY WIRES
(if applicable)
HOST LIGHTING FIXTURE
Step 3 (Continued):
d. When wiring the light engine, either utilize the
provided grommets in the knockouts located on
the junction box covers on the top of the light
engine, or remove the junction box covers from the
light engine completely. Connect wires as shown
in wiring diagram. Tuck the wiring above the Side
Panel closest to the Light Engine junction box so
that they are out of the way.
NOTE: If additional wiring is needed in order to
complete the installation of this upgrade kit, then
it is recommended to utilize the wiring from the
original host lighting fixture that was discarded.
e. Swing the free hanging end of the Light Engine
up and ensure that the Mount Pin slides into the
Mount Pin Pivoting Guide. Continue to push up
until the Mount Pin snaps into the Mount Pin Hole
of each side of the Light Engine.
f. The unit is now ready to use. Reconnect power to
the fixture and turn on light to test connections.
REMOVING LIGHT ENGINE
Step 4:
a. To remove the UPKIT fixture, first disconnect the
power going to the fixture. Then remove the Mount
Plugs from one end of the fixture by prying them
out using a sharp, small tool.
b. Once the Mount Plug is removed, a slot in the
Mount Pin is visible. Insert a flathead screwdriver in
the slot and slide in the Mount Pin away from the
center of the fixture. This will disengage one side of
the Light Engine. Repeat the process for the other
side until the Light Engine can swing down.
c. When the Light Engine is hanging from the
fixture, disconnect the power connections and
grounding wires.
d. Remove the Mount Plugs from this end and use
the screwdriver to disengage the Light Engine
from the fixture.
e. Remove the Side Panels and then take out the
End Mounts.
NOTE: The retrofit kit is accepted as a
component of a luminaire where the
suitability of the combination shall
be determined by CSA or Authorities
having jurisdiction.
4b
3f
3e
3d
Mount Pin
Slot
3e
Mount Pin
Mount
Pin Hole
Mount Pin
Pivoting Guide
4a
Mount Plug
