background image

 

        

 

 

 
 

Contact

 

Details

 

 

Please

 

note

 

that

 

some

 

of

 

the

 

contact

 

details

 

on

 

this

 

PDF

 

document

 

may

 

not

 

be

 

current.

 

 

Please

 

use

 

the

 

following

 

details

 

if

 

you

 

need

 

to

 

contact

 

us:

 

 

Telephone:

 

0844

 

879

 

3588

 

Email:

 

[email protected]

 

 
 

The

 

Help

 

Centre

 

section

 

of

 

this

 

website

 

also

 

features

 

a

 

wide

 

range

 

of

 

information

 

which

 

may

 

be

 

of

 

use

 

to

 

you

 

and

 

is

 

available

 

24

 

hours

 

a

 

day.

 

It

 

includes:

 

 

 

Operating

 

and

 

installation

 

instructions

 

downloads

 

 

Request

 

a

 

repair

 

 

Where

 

to

 

buy

 

our

 

products

 

 

Literature

 

downloads

 

 

Heating

 

requirement

 

calculator

 

 

www.credaheating.co.uk/help

centre

 

A division of GDC Group Ltd 
Millbrook House   Grange Drive   Hedge End   Southampton   SO30 2DF 
www.credaheating.co.uk

 

Registered No: 1313016 England

VAT GB 287 1315 50004 

EEE Producer Registration Number – 

WEE/GE0057TS 

Paper from sustainable sources 

Summary of Contents for NewEra 70305S










Reviews: