Creative Playthings WILLIAMSBURG SH 3200-000 Assembly Manual Download Page 13

Page: 13 / 18

WILLIAMSBURG WITH TENT ROOF

19687-100 Rev U (09-20)

Assembly

Page 13

ASSEMBLY INSTRUCTIONS

STEP 11 — Platform Boards:

Layout all nine Platform Boards (O) on the inside and outside

stringers. Check each board to make sure the best looking

surface faces up. Space the platform boards evenly between the

narrow platform boards. Fasten each platform board using six

#10 x 2" Screws.

STEP 12 — Side Wall Supports:

Fasten each Side Wall Support (S) to the corner posts above a

platform side using four 5/16 x 4" hex bolt assemblies.

#10 x 2" Screws

5/16 x 4" Hex Bolts

STEP 13 — End Tent Supports:

Fasten the End Tent Supports (X) to the corner posts above the

platform ends using four 5/16 x 4" hex bolt assemblies for each

support. Arrange the parts so the holes at the center align near

the top edge.
Note: you will need to loosen these fasteners when installing the

tent in a later step.

Summary of Contents for WILLIAMSBURG SH 3200-000


















Search results

Summary of Contents for WILLIAMSBURG SH 3200-000

Reviews:

Related manuals for WILLIAMSBURG SH 3200-000

Brands by name

Popular brands

Creative Playthings WILLIAMSBURG SH 3200-000, Assembly Manual

Search results

Summary of Contents for WILLIAMSBURG SH 3200-000

Reviews:

Related manuals for WILLIAMSBURG SH 3200-000

Brands by name

Popular brands