Creative Playthings SH304-101 Assembly Manual Download

Page: 1 / 8

A 2 33601-102 Angled Rail 2 x 4 x 108"

B 1 33602-102 Center Rail 2 x 4 x 108"

C 9 32298-102 Rock Board 5/4 x 6 x 46"

D 9 32299-102 Spacer Board 5/4 x 6 x 46"

E 1 33565-102 Top Rope Board 5/4 x 6 x 46"

F 1 32300-102 Bench Seat 2 x 6 x 40"

G 2 32301-102 Bench Support 2 x 6 x 10-5/8"

H 1 32302-102 Bench Cleat 2 x 3 x 31-1/4"

I* 1 32834-102 Center Post 4 x 4 x 67-1/8"

(* Used only on gyms with gambrel tents)

1 40400-100 Climbing Rope Assembly

MODEL #SH304-101

ASSEMBLY MANUAL

PINNACLE ROCK WALL

All hardware on this set is specially coated for corrosion

resistance. If non-Creative Playthings hardware is used,

it MUST be galvanized or stainless steel.

COMPONENT PARTS

SPECIAL NOTES

TOOLS REQUIRED FOR ASSEMBLY

•

The Pinnacle Rock Wall is not intended for children

under six years of age.

• The Pinnacle Rock Wall

must

be fastened to the Wall

Support at the

rear

of your Playset.

• The Pinnacle Rock Wall can not be used in conjunction with

any option that would fasten to the rear wall of a Playset.

• All the Hand Holds supplied must be fastened to your

Rock Wall. There should be no unused mounting holes

left on the Rock Wall. Unused holes could present a

finger entrapment hazard to your child.

• Keep Hand Holds clean so that they can be inspected

for cracks and sharp edges. Replace any damaged

Hand Holds.

• Replace any bolts or weld nuts that become stripped or

cross threaded.

• Please review your original Playset Assembly Manual

and your Owners Manual before assembly of your

Pinnacle Rock Wall.

• Provide a soft surface free from obstructions 6' out from

the base of the Pinnacle Rock Wall. See your original

Playset Instructions for recommended play surfaces.

• 7/16" & 1/2" Socket Wrench

• 3/8" & 1" Diameter Drill. (1/4" may be needed)

• Phillips Screwdriver or Drill with Screw Tip

• Tape Measure

18 Climbing Rocks

Weld Nut

Lock Washer

Flat Washer

Hex Bolt

Screw

SH304-101 Pine

Access Ladder Bracket

Lag Screw

Important: Set the base of

the Rock Climber into the

ground to the level of the

bottom of the Rope

See the last page for Part Number Reference.

Summary of Contents for SH304-101









Search results

Summary of Contents for SH304-101

Reviews:

Related manuals for SH304-101

Brands by name

Popular brands

Creative Playthings SH304-101, Assembly Manual

Search results

Summary of Contents for SH304-101

Reviews:

Related manuals for SH304-101

Brands by name

Popular brands