manualshive.com logo in svg

CREATIVE ELECTRONICS SMC-3303X, Operation Manual

Share
Download
CREATIVE ELECTRONICS SMC-3303X Operation Manual Download Page 24

- 21 - 

6. MAINTENANCE 

 

6.1 Inspection 

 

Inspect the instrument at regular intervals so that it maintains its initial performance for a long time. 

 

Check the input power cord for damage of the vinyl cover and overheating of the plug and cord stopper. Check the 

terminal screws and binding posts for loosening.   

 

Remove  dust from the inside of the casing and ventilation holes of the cover by using a compressed air of the 

exhaust air of a vacuum cleaner. 

 

 

6.2 Fuse Replacement 

Steps 

1.

 

Take off the power cord and remove the fuse socket using a minus driver. 

 

2.

 

Replace the fuse in the holder. 

 

Fuse rating 

110V: T6.3A/250V 

220V: T3.15A/250V 

 

 

6.3 Cleaning 

 

Before cleaning, disconnect the AC mains. 

 

To clean the power supply, use a soft cloth dampened in a solution of mild detergent and water. Do not 
spray cleaner directly onto the instrument, since it may leak into the cabinet and cause damage. 

 

Do not use chemicals containing benzene, benzene, toluene, xylene, acetone, or similar solvents. 

 

Do not use abrasive cleaners on any portion of the instrument. 

 

 

 

 

 

 

 

 

 

No.35, Hartron Complex, Sector-18, Electronic City, Type-A, Udyog Vihar, Phase-IV, Gurugram 122015 Haryana, India

 

Tel: +91-124-4909 850; Fax:

 

+91-11 66173638 

Email:

Summary of Contents for SMC-3303X

























Reviews:

No comments

Brands by name

Popular brands

Load more brands