manualshive.com logo in svg

CREATIVE ELECTRONICS SMC-3303X, Operation Manual

Share
Download
CREATIVE ELECTRONICS SMC-3303X Operation Manual Download Page 13

- 10 - 

 

 

 

Output rating 

Fixed 2.5V/3.3V/5V, 3A 

 

 

No tracking 

Series/Parallel 

mode 

CH3 does not have tracking series/parallel mode. Also, CH3 output is not affected by CH1 and 2 

modes. 

 

 

Panel operation 

1.

 

Connect the load to the front panel CH3 +/- terminal. 

 

 

2.

 

Select the output voltage from 2.5V, 3.3V and 5V, using the CH3 

voltage selector switch.   

3.

 

To turn on the output, press the output key. The key LED turns on.  

 

 

 

 

CC to CV 

When the output Current level exceeds 3A, the overload indicator turns red and CH3 operation mode 

switches from Constant Voltage to Constant Current. 

 

Note: “overload” in this case does not mean an abnormal operation. 

 

 

 

 

3.3 CH1/CH2 Tracking Series Mode   

Background 

Tracking series operation doubles the Voltage capacity of the power supply series by internally 

connecting CH1 (Master) and CH2 (Slave) in series and combining the output to a single channel. 

CH1 (Master) controls the combined Voltage output level. 

The following describes two types of configurations depending on the common ground usage. 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for SMC-3303X

























Reviews:

No comments

Brands by name

Popular brands

Load more brands