Crane Barnes Simplex OGV Series Installation Manual Download | Manualshive

Page: 14 / 25

background image

14

FIGURE 10

STEPS & TIPS:

• Once the lifting device is attached to the pump, secure it so it will not fall into basin.

• Thread flex hose assembly into check valve on pump. Remove upper valve nut assembly as shown

and secure to other end of the flex hose assembly.

• Secure pump cord(s) and hose assembly so they will not fall into basin and lower into basin.

• Follow all O.S.H.A. guidelines.

• NEVER LOWER OR RAISE PUMP BY THE CORD!

• Attach union on flexible hose to station shut-off valve.

STEP 7.

Sliding Pump Into Basin

«
...
12
13
14
15
16
...
»

Summary of Contents for Barnes Simplex OGV Series


























Reviews:

No comments

Related manuals for Barnes Simplex OGV Series

Brand: dafi Pages: 12

Brand: York International Pages: 87

Brand: EarthLinked Pages: 6

Brand: SAER Elettropompe Pages: 36

Brand: A.O. Smith Pages: 62

Brand: Quincy Compressor Pages: 122

Brand: York Pages: 84

Brand: Edwards Pages: 16

jumbo floodfighter

Brand: Davey Pages: 8

Brand: Homa Pages: 24

OmniSpense ELITE

Brand: Wheaton Pages: 34

Altherma 3 M Series

Brand: Daikin Pages: 24

Basement Sentry 507

Brand: Zoeller Pages: 8

Brand: Giant Pages: 12

Flame Guard Safety System

Brand: American Water Heater Pages: 29

BioPressure II 6000

Brand: ubbink Pages: 64

Brand: Wacker Neuson Pages: 52

Brand: Pfeiffer Vacuum Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands