manualshive.com logo in svg

Crane BARNES 4SE Series, Installation And Operation Manual

Share
Download
Crane BARNES 4SE Series Installation And Operation Manual Download Page 4

SECTION: A- PUMP SPECIFICATIONS

DISCHARGE:

3 (76) & 4" (102) 125 lb, Horizontal

LIQUID TEMPERATURE:

104°F (40°C) Continuous.

VOLUTE:

Cast Iron ASTM A-48, Class 30.

MOTOR HOUSING:

Cast Iron ASTM A-48, Class 30.

SEAL PLATE:

Cast Iron ASTM A-48, Class 30.

IMPELLER:

 

Design: 

2 Vane, Open, With Pump Out
Vanes On Back Side. Dynamically
Balanced. ISO G6.3.

Material: 

Cast Iron ASTM A-48 Class 30.

SHAFT:

416 Stainless Steel

SQUARE RINGS:

 Buna-N

HARDWARE:

300 Series Stainless Steel

PAINT:

Air Dry Enamel.

SEAL:

Design: 

Single Mechanical, Oil-Filled Reservoir,
Secondary Exclusion Seal.

Material: 

Rotating Face - Carbon
Stationary Face - Ceramic
Elastomer - Buna-N
Hardware - 300 Series Stainless

CABLE ENTRY:

15ft. (4.5M) Cord (Plug On 115 Volt),
Pressure Grommet For Sealing And
Strain Relief

.

SPEED:

1750 RPM (Nominal)

UPPER BEARING:

 

Design: 

Sleeve

Lubrication:

 Oil

Load:

 Radial

LOWER BEARING:

 

Design:

 

Single Row, Ball

Lubrication:

 Oil

Load:

 

Radial & Thrust

MOTOR: 

Design:

 

NEMA L-Single Phase, NEMA B-Three
Phase Torque Curve. Completely 
Oil-Filled, Squirrel Cage Induction.

Insulation:

 Class 

A. 

SINGLE PHASE:

Permanent Split Capacitor (PSC). 
Includes Overload Protection In Motor.

THREE PHASE:

 

Tri Voltage 200-230/460;
Requires Overload Protection to be
Included in Control Panel.

OPTIONAL EQUIPMENT:

Seal Material, Impeller Trims, N/C
Temperature Sensor with cable for 
3 phase pumps, Additional Cable
CSA Listed on 3 phase pumps.

18.31

(465)

6.06

(154)

12.24

(311)

7.37

(187)

4.87

(124)

9.74

(247)

inches

(mm)

4

Manual Index

Summary of Contents for BARNES 4SE Series

























Reviews:

No comments

Brands by name

Popular brands

Load more brands