manualshive.com logo in svg

Crane BARNES 4SE Series, Installation And Operation Manual

Share
Download
Crane BARNES 4SE Series Installation And Operation Manual Download Page 2

TABLE OF CONTENTS

WARNINGS AND SAFETY PRECAUTIONS........................................................................3

A. PUMP SPECIFICATIONS.....................................................................................................4

B. GENERAL INFORMATION...................................................................................................5

C. INSTALLATION ....................................................................................................................5 - 6

ELECTRICAL DATA .............................................................................................................7

D. START-UP OPERATION ......................................................................................................7

E. PREVENTATIVE MAINTENANCE........................................................................................8

F. SERVICE and REPAIR .........................................................................................................8 - 12

TROUBLE SHOOTING .........................................................................................................13

G. REPLACEMENT PARTS ......................................................................................................14

CROSS-SECTION  (Fig. 8)...................................................................................................15
EXPLODED VIEW  (Fig. 9)...................................................................................................16
PARTS LIST  ........................................................................................................................17 - 18

WARRANTY INFORMATION ...............................................................................................19
WARRANTY
START-UP REPORT
WARRANTY REGISTRATION

SPECIAL TOOLS AND EQUIPMENT

INSULATION TESTER  (MEGGER)
DIELECTRIC TESTER
SEAL TOOL KIT  ( see parts list)
PRESSURE GAUGE KIT  (see parts list)

Other brand and product names are trademarks or registered trademarks of their respective holders.
® Barnes is a registered trademark of Barnes Pumps, Inc.
© Barnes Pumps, Inc. 1994, 1997, 1998, 2002               Alteration Rights Reserved.                                              Printed in U.S.A.

2

Manual Index

Summary of Contents for BARNES 4SE Series

























Reviews:

No comments

Brands by name

Popular brands

Load more brands