Crane Barnes 130174 Manual Download Page 1

Page: 1 / 10

A Crane Co. Company

BARNES

SEAL KIT P/N 130178

SERVICE KIT P/N 130174

Submersible Pump

IMPORTANT!

Read all instructions in this manual before operating pump.

As a result of Crane Pumps & Systems, Inc., constant product improvement program,

product changes may occur. As such Crane Pumps & Systems reserves the right to

change product without prior written notiﬁ cation.

420 Third Street

83 West Drive, Brampton

Piqua, Ohio 45356

Ontario, Canada L6T 2J6

Phone: (937) 778-8947

Phone: (905) 457-6223

Fax: (937) 773-7157

Fax: (905) 457-2650

www.cranepumps.com

Form No. 130185-Rev. C

Series: 3SE-DS
1750 RPM, 60 Hz.

Series: 4SE-L
1.9 & 2.8HP,
1150 RPM, 60 Hz.

Series: 4SE-L
2.8, 3.7 & 5HP,
1750 RPM, 60 Hz.

Series: 4SE-L
5HP, 3450 RPM, 60 Hz.

Series: 4SE-L
1.6, 2.1 & 2.8HP
(1.2, 1.6 & 2.1kW),
1450 RPM, 50 Hz.

Double Seal

Manual Index

Summary of Contents for Barnes 130174











Search results

Summary of Contents for Barnes 130174

Reviews:

Related manuals for Barnes 130174

Brands by name

Popular brands

Crane Barnes 130174, Manual

Search results

Summary of Contents for Barnes 130174

Reviews:

Related manuals for Barnes 130174

Brands by name

Popular brands