CRAIN 835 Instructions Manual Download Page 3

Page: 3 / 8

Hold onto the plastic housing, then push hard on the hex wrench counter-clockwise

to open. If the blade is very hard to remove, use a pair of locking pliers to hold
the blade, and add an extension tube on the hex wrench for extra leverage.

INSTALLING BLADES - CARBIDE BLADE (#836):

Switch off and unplug saw. Refer to Figure 3.

Place the blade spacer over the spindle.

Place blade driver (#1835-13) on top of the blade

spacer with bottom slot engaged with the spindle.

Place the blade on top of the blade driver with the

two blade driver nubs extending through the two
driver holes in the blade.

Insert and re-tighten the blade screw. Push in the

spindle lock to tighten. Tighten firmly before use.

INSTALL MASONRY (#805) OR
DIAMOND BLADE (#822):

Switch off and unplug saw. Refer to Figure 4.

Place the blade spacer over the spindle.

Place the blade on top of the blade spacer.

Place the blade clamp (#1812-P) through the arbor

hole of the blade with the bottom slot of the blade
clamp engaged with the spindle.

Insert and re-tighten the blade screw. Push in the

spindle lock to tighten. Tighten firmly before use.

The #822 Diamond Blade is sold separately.

BLADE HEIGHT ADJUSTMENT:

Switch off and unplug saw. Refer to Figure 5.

Loosen height locking wing screws 1 to 2 turns.

Turn the two height adjustment three-arm knobs

clockwise to increase blade height and counter
clockwise to decrease height.

It is best to turn both height adjustment three-

arm knobs at the same time to ensure the blade
is set parallel with the floor.

Both the front of the height adjuster and the inside of the height adjuster have 10

reference lines, in 3/32" increments (.093" which is one blade thickness).

Figure 3

BLADE
SPACER

HEX
WRENCH

BLADE
SCREW

#1835-13
BLADE
DRIVER
(BOTTOM):

#836

SLOT
ENGAGES
SPINDLE

SPINDLE

UNPLUG THE SAW. REMOVE HEX

WRENCH BEFORE STARTING.

BLADE
SPACER

HEX
WRENCH

BLADE
SCREW

#1812-P
BLADE
CLAMP
(BOTTOM):

#805
OR
#822

SLOT
ENGAGES
SPINDLE

SPINDLE

Figure 4

UNPLUG THE SAW. REMOVE HEX

WRENCH BEFORE STARTING.

BLADE
DRIVER
DRIVE
NUBS:

REFERENCE
LINES

WING
SCREW

HEIGHT ADJUSTER

BOTTOM EDGE
OF HOUSING

Figure 5

THREE ARM
KNOB

Summary of Contents for 835









Search results

Summary of Contents for 835

Reviews:

Brands by name

Popular brands

CRAIN 835, Instructions Manual

Search results

Summary of Contents for 835

Reviews:

Brands by name

Popular brands