background image

 

 

 

 

WARNING:Changes or modifications to this unit  

not expressly approved by the party responsible 

for compliance could void the user’s authority to 

operate the equipment. 
NOTE: This equipment has been tested and 

found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide 

reasonable protection against harmful interference

in a residential installation. This equipment 

generates, uses, and can radiate radio frequency 

energy and, if not installed and used in 

accordance with the instructions, may cause 

harmful interference to radio communications. 

However, there is no guarantee that interference 

will not occur in a particular installation. If this 

equipment does cause harmful interference to 

radio or television reception, which can be 

determined by turning the equipment off and on, 

the user is encouraged to  try to correct the

interference by one or more of the following 

measures:     

Reorient or relocate the receiving antenna.

Increase the separation between the 

equipment and receiver.

Connect the equipment into an outlet on a 

circuit different from that to which the receiver 

is connected.

Consult the dealer or an experienced radio/TV 

technician for help. 


FCC Warnings

FCC NOTICE:

To assure continued compliance, follow the attached 

installation instructions and use only shielded cables 

when connecting to other devices. Modifications not 

authorized by the manufacturer may void user’s 

authority to operate this device.

Summary of Contents for CHT923
















Reviews: