background image

3 – English

GENERAL POWER TOOL SAFETY WARNINGS

WARNING  

Read all safety warnings and all 

instructions. 

Failure to follow the warnings and 

instructions may result in electric shock, fire and/or 
serious injury.

Save all warnings and instructions for future 

reference. 

The term “power tool” in the warnings refers 

to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.

WORK AREA SAFETY

 

Keep work area clean and well lit. 

Cluttered or dark 

areas invite accidents.

 

Do not operate power tools in explosive 
atmospheres, such as in the presence of flammable 
liquids, gases, or dust. 

Power tools create sparks 

which may ignite the dust or fumes.

 

Keep children and bystanders away while operating 
a power tool. 

Distractions can cause you to lose 

control

.

ELECTRICAL SAFETY

 

Power tool plugs must match the outlet. Never 
modify the plug in any way. Do not use any adapter 
plugs with earthed (grounded) power tools. 

Unmodified plugs and matching outlets will reduce risk 
of electric shock.

 

Avoid body contact with earthed or grounded 
surfaces such as pipes, radiators, ranges and 
refrigerators. 

There is an increased risk of electric 

shock if your body is earthed or grounded.

 

Do not expose power tools to rain or wet 
conditions. 

Water entering a power tool will increase 

the risk of electric shock.

 

Do not abuse the cord. Never use the cord for 
carrying, pulling or unplugging the power tool. Keep 
cord away from heat, oil, sharp edges, or moving 
parts. 

Damaged or entangled cords increase the risk 

of electric shock.

 

When operating a power tool outdoors, use an 
extension cord suitable for outdoor use. 

Use of 

a cord suitable for outdoor use reduces the risk of 
electric shock.

 

If operating a power tool in a damp location is 
unavoidable, use a ground fault circuit interrupter 
(GFCI) protected supply. 

Use of a GFCI reduces the 

risk of electric shock.

 

Use battery only with charger listed.

 For use with 

19.2V nickel-cadmium and 19.2V lithium-ion battery 
packs, see tool/appliance/battery pack/charger 
correlation supplement 988000-272.

PERSONAL SAFETY

 

Stay alert, watch what you are doing and use 
common sense when operating a power tool. Do 
not use a power tool while you are tired or under the 
influence of drugs, alcohol or medication. 

A moment 

of inattention while operating power tools may result in 
serious personal injury.

 

Use personal protective equipment. Always wear eye 
protection. 

Protective equipment such as dust mask, 

non-skid safety shoes, hard hat, or hearing protection 
used for appropriate conditions will reduce personal 
injuries.

 

Prevent unintentional starting. Ensure the switch 
is in the off-position before connecting to power 
source and/or battery pack, picking up or carrying 
the tool. 

Carrying power tools with your finger on the 

switch or energising power tools that have the switch on 
invites accidents.

 

Remove any adjusting key or wrench before turning 
the power tool on. 

A wrench or a key left attached to 

a rotating part of the power tool may result in personal 
injury.

 

Do not overreach. Keep proper footing and balance 
at all times. 

This enables better control of the power 

tool in unexpected situations.

 

Dress properly. Do not wear loose clothing or 
jewellery. Keep your hair, clothing and gloves away 
from moving parts. 

Loose clothes, jewellery or long 

hair can be caught in moving parts.

 

If devices are provided for the connection of dust 
extraction and collection facilities, ensure these are 
connected and properly used. 

Use of dust collection 

can reduce dust-related hazards.

 

Do not wear loose clothing or jewelry. Contain long 
hair. 

Loose clothes, jewelry, or long hair can be drawn 

into air vents.

 

Do not use on a ladder or unstable support. 

Stable 

footing on a solid surface enables better control of the 
power tool in unexpected situations.

POWER TOOL USE AND CARE

 

Do not force the power tool. Use the correct power 
tool for your application. 

The correct power tool will 

do the job better and safer at the rate for which it was 
designed.

 

Do not use the power tool if the switch does not turn 
it on and off. 

Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

 

Disconnect the plug from the power source and/or 
the battery pack from the power tool before making 
any adjustments, changing accessories, or storing 
power tools. 

Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

Summary of Contents for SIERRA CIRCULAR 315.CT2040

































Reviews: