...the light bulb blinks 3 times.
1
Press any programmed PIN, then press and hold
the
*
button until...
+
? ? ? ?
PIN
2
+
? ? ? ?
Temporary PIN
Enter the temporary 4-digit PIN of your
choice, then press the ENTER button.
The light bulb will blink
4 times.
Then press
the button.
3
+
Press the number
of hours the
temporary PIN
will work (up to 255).
3
OR
Then press
the # button.
+
Press the number
of openings the
temporary PIN
will work (up to 255).
1 blink
1 blink
To test, press the temporary
PIN, then press the ENTER
button. The garage door opener
will activate. If the temporary
PIN was set for a number of
openings, the test will use up
one opening.
To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3.
*
Replace the battery when the keypad
becomes dim or does not light after a button
is pressed.
Dispose of old battery properly.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
PROGRAM A TEMPORARY PIN
OPERATION
The garage door opener activates when the PIN and ENTER button are
pressed. The keypad will blink for 15 seconds, during that time the
ENTER button can be used to stop, start or reverse the door.
If the wrong number is accidentally pressed, press the correct PIN then
the ENTER button. The keypad will transmit only the last four digits that
were pressed before the ENTER button.
ONE BUTTON CLOSE:
The keypad has a feature that allows the door to be
closed using the ENTER button instead of a PIN.
NOTE:
This feature is not available on garage door openers manufactured
prior to 2006 or an external receiver.
To deactivate the one button close feature:
1
Press and hold the 1 and 9 buttons for 10 seconds.
2
The keypad will blink four times when the one button close feature is
deactivated.
To activate the one button close feature:
1
Press and hold the 1 and 9 buttons for 10 seconds.
2
The keypad will blink twice when the one button close feature is
activated.
REPLACEMENT PARTS
9V Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A25
Keypad cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D621
Battery cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D541
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
NOTE:
This feature is not available on garage door openers that have a
green Learn button or an external receiver.
A temporary 4-digit PIN can be programmed to allow access to
visitors. Each programmed PIN can program one temporary PIN. The
temporary PIN can be set for a number of hours or a number of door
openings. The temporary PIN cannot be the same as any previously
programmed PIN.
BATTERY
INSTALLATION
1
Select a location to mount the keypad at a minimum height of 5
feet (1.5 m) out of the reach of children.
2
Remove battery cover and battery.
3
Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole.
4
Install the top screw, allowing 1/8 inch (3.2 mm) to protrude
above the surface. Position the keypad over the top screw.
5
Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install
the bottom screw. Do not overtighten to avoid cracking the plastic
housing.
6
Reinstall battery and replace cover.
9V Battery
Call: 888-331-4569
www.craftsman.com
NUMBER OF HOURS
NUMBER OF OPENINGS
