background image

5

English

 

CAUTION:

• 

This product is not designed to be directly 

lifted with a fork lift, or to be towed with any 

mechanical devices.

• 

DO NOT exceed the maximum weight capacity for 

each drawer or shelf.

• 

Distribute contents of loaded drawers evenly.

 DO NOT 

position all contents of a drawer in the front portion of 
the drawer. 

• 

This product should be empty when transporting by 

vehicle.

 Properly secure when transporting. 

• 

DO NOT exceed maximum product weight, including 

contents.

 See 

Capacities

 for more information.

• 

As with all metal products, this product can contain 

burrs and sharp edges.

 Wear protective gloves 

during assembly.

• 

Use adequate manpower when assembling and 

moving this unit.

 Failure to do so may cause personal 

injury or product damage.

 

WARNING:

• 

DO NOT alter this product in any manner.

 For 

example, do not weld external lockbars or attach 
electrical equipment.

• 

Keep the product on level surfaces.

 The product 

may become unstable and tip if stored or moved on an 
uneven surface.

• 

Wall and floor cabinets MUST be attached to a stud in 

a wood frame wall.

 Failure to do so may cause personal 

injury or product damage.

• 

Hardware is provided for wood frame wall use only.

 

Concrete or other surfaces will require other hardware 
(not provided). Use appropriate hardware per your local 
building codes. Failure to do so may cause personal injury 
or product damage.

• 

DO NOT allow unsupervised children to play on 

or with the cabinet.

 Failure to adhere to instructions 

regarding restrictions to the number of open drawers (even 
when empty) could cause tipover, resulting in serious injury 
or death.

 

DANGER:

• 

DO NOT stand on this product.

 You may fall or cause 

product to tip.

• 

DO NOT open more than one drawer at one time.

 The 

product may become unstable and tip.

• 

DO NOT step in the drawers.

 You may fall or cause 

product to tip.

• 

DO NOT mount this product on a truck bed or any 

other moving object.

General Safety Rules for Cabinets 

and Chests

 

CAUTION:

 Read and follow all Safety Rules and 

Operating Instructions before assembly and first use of 
this product.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert 
symbols and words to alert you to hazardous situations and 
your risk of personal injury or property damage.

 

DANGER:

 Indicates an imminently hazardous 

situation which, if not avoided, 

will 

result in 

death or 

serious injury

.

 

WARNING:

 Indicates a potentially hazardous situation 

which, if not avoided, 

could

 result in 

death or 

serious injury

.

 

CAUTION:

 Indicates a potentially hazardous situation 

which, if not avoided, 

may

 result in 

minor or 

moderate injury

.

 

(Used without word) Indicates a safety related message.

NOTICE:

 Indicates a practice 

not related to 

personal injury

 which, if not avoided, 

may

 result in 

property damage

.

Service Parts

Call 888‑331‑4569 for Service Parts.

Locating Model # Information

Model numbers and other information required for service 
parts are located on a label on the interior right side of the 
top most drawer.

CAPACITIES

 

WARNING:

 To reduce the risk of injury, do not 

overload cabinet.

Floor Cabinet

•  The maximum weight for each shelf in a door should be 

no more than 7 lbs.

•  The maximum weight for each full shelf in cabinet should 

be no more than 100 lbs.

•  The maximum product weight, including contents, 

should be no more than 600 lbs.

Wall Cabinet

•  The maximum weight for shelf in cabinet should be no 

more than 50 lbs.

•  The maximum product weight, including contents, 

should be no more than 150 lbs when mounted directly 
to wall studs.

Base Cabinet

•  The maximum weight for each drawer should be no 

more than 100 lbs.

•  The maximum weight for each shelf should be no more 

than 100 lbs.

•  The maximum product weight, including contents, 

should be no more than 800 lbs.

English (original instructions)

Summary of Contents for CMST98239BK























Reviews: