Craftsman CMEW300, Instruction Manual

Page: 10 / 36

English
8
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING:
Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
Repairs
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including power cord repairs, and brush inspection
and replacement, when applicable) should be
performed by a CRAFTSMAN factory service center or
a CRAFTSMAN authorized service center. Always use
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
•
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
•
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.craftsman.com/
To Reinstall Blade
1. Slide the blade sideways into the holder until it is
against the end stop. Blade groove must be toward back
of unit.
2. Securely tighten the three nuts using the wrench
supplied. Rotate the blade drum 180° and repeat for
other blade.
3. Always replace both blades.
Drive Belt (Fig. N)
To Replace Belt
1. Loosen the three screws shown in Figure N and remove
the belt cover.
2. Remove old belt.
3. Place new belt over front pulley then rotate belt
clockwise while pushing belt onto back pulley.
4. Attach belt cover and securely tighten screws.
Fig. N
WARNING:
Turn off and unplug unit before cleaning
chip discharge chute.Clean the chip discharge
chute
6 regularly. Blow dust and chips from the
dust port with clean dry air. ALWAYS WEAR SAFETY
GLASSES.
Three Year Limited Warranty
CRAFTSMAN will repair or replace, without charge, any
defects due to faulty materials or workmanship for three
years from the date of purchase. This warranty does not
cover part failure due to normal wear or tool abuse. For
further detail of warranty coverage and warranty repair
information, visit
www.craftsman.com
or call
1-888-331-4569 . This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
90 DAY MOnEY BACK gUARAnTEE
If you are not completely satisfied with the performance of
your CRAFTSMAN Power Tool or Nailer for any reason, you
can return it within 90 days from the date of purchase with
a receipt for a full refund – no questions asked.
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call
1-888-331-4569 .