11
English
Loading the Tool (Fig. A)
WARNING:
Keep the tool pointed away from yourself
and others.
WARNING:
Never load nails with the contact trip or
trigger activated.
WARNING:
Always remove battery pack before
loading or unloading nails.
CAUTION:
Keep fingers clear of pusher latch track to
prevent injury.
WARNING:
The trigger lock‑off should always be
engaged whenever any adjustments are made or when
tool is not in use.
1. Turn the nailer upside down.
2. Slide the spring-loaded pusher latch
8
to the base of the
magazine to lock it into place.
3. Drop nail strips into the loading slot of the magazine,
making sure the nail heads align correctly with the slot
opening. (Refer to
Nail Specifications
to determine
compatible size.)
4. Keeping fingers clear of the track, close the magazine by
releasing the pusher latch. Carefully allow the latch to
slide forward and engage the nail strip.
Unloading the Tool
WARNING:
The trigger lock‑off should always be
locked off whenever any adjustments are made or
when tool is not in use.
1. Slide the spring-loaded pusher latch to the base of the
magazine to lock it into place.
2. Tip the tool up until the fastener strip slides freely out of
the magazine.
3. With battery removed, check the nosepiece to verify
there are no nails remaining.
Using the Trigger Lock-Off (Fig. F)
WARNING:
To reduce the risk of serious personal
injury, do not keep trigger depressed when tool is not in
use. Keep the trigger lock‑off switch LOCKED when the
tool is not in use.
WARNING:
To reduce the risk of serious personal
injury, lock off trigger, disconnect battery pack
from tool and remove nails from magazine before
making adjustments.
Each nailer is equipped with a trigger lock-off
2
which when
pushed to the right prevents the tool from firing a nail by
locking the trigger and bypassing power to the motor.
When the trigger lock-off is pressed to the left, the tool will
be fully operational. The trigger lock-off should always be
locked off (Fig. F) whenever any adjustments are made or
when tool is not in immediate use.
NOTICE:
Do not store tool with battery pack installed.
To prevent damage to the pack and to ensure best
battery life, store battery packs out of the tool or
charger in a cool, dry location.
Proper Hand Position (Fig. E)
WARNING:
To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
12
.
Installing and Removing the Battery Pack
(Fig. D)
nOTE:
For best results, make sure your battery pack is
fully charged.
To install the battery pack
11
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
13
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
Preparing the Tool
NOTICE: NEVER
spray or in any other way apply
lubricants or cleaning solvents inside the tool. This
can seriously affect the life and performance of
the tool.
nOTE:
The battery pack is not fully charged out of the carton.
Follow instructions outlined (refer to
Charging a Battery
).
1. Read the
Nailer Safety Warnings
section of this manual.
2. Wear eye and ear protection.
3. Remove battery from tool.
4. Ensure magazine is empty of all fastners.
5. Check for smooth and proper operation of contact trip
and pusher assemblies. Do not use tool if either assembly
is not functioning properly.
nEVER
use a tool that has
the contact trip restrained in the actuated position.
6. Keep tool pointed away from yourself and others.
7. Insert fully charged battery pack.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
