Craftsman 944.364701 Owner'S Manual Download

Page: 8 / 16

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OP ER AT ING YOUR

LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself

with the location of various controls and adjustments. Save this manual for future refer-

ence.

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

OPERATION

Wheel adjuster

(on each wheel)

Operator presence control bar

Handle knobs

MEETS CPSC SAFETY REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform to the safety standards of the

American National Standards Institute and the U.S. Consumer Product Safety Com mis-

sion.

WARNING:

The blade turns when the engine is running.

Operator presence control bar –

must

be held down to the handle to start the

engine. Release to stop the engine.

Primer

– pumps additional fuel from the

carburetor to the cylinder for use when

starting a cold engine.

Starter handle –

used for starting engine.

Drive control bar –

used to engage pow-

er-pro pelled forward mo tion of mower.

Mulcher door –

allows con ver sion to

discharging or bagging operation.

Grass

catcher

Drive control bar

Engine oil cap

with dipstick

Air filter

Gasoline filler cap

Housing

Mulcher door

Starter

handle

Spark

plug

IMPORTANT:

This lawn mower is shipped

WITHOUT OIL OR GASOLINE in the engine.

NOTE:

Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.

The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.

Muffler

CRAFTSMAN

ROT

ARY LA

WN MOWER - - MODEL NUMBER

944.364701

NOTE:

All component dimensions given in U

.S. inches. 1 inch = 25.4 mm.

IMPORT

ANT

Use only Original Equipment Manufacturer (O

.M.) replacement parts. F

ailure to do so could be hazardous, damage your lawn mo

wer and void your warranty

KEY P

ART

. NO

DESCRIPTION

KEY P

ART

. NO

DESCRIPTION

586033302

Drive Control Assembly

(Includes

Cable)

4 197480

-Ring

194185X428

Control Bar

, Drive

12 580364604

Belt,

Drive

581680801

Gear Case Assembly

, Complete

14 586963001

ulley

, Drive

581497908

Wheel Adjuster

, Rear

, RH

581497907

Wheel Adjuster

, Rear

, LH

18 701037

Selector

Knob

20 580806901

Debris

Shield

17000510

Screw

, Hex Head 5/16-18

581313802

Mounting Bracket, Debris Shield

26 421516X004

Bracket,

Gearcase

27 67725

asher

12000058

E-Ring 7/16

581840401

Cover

, Dust, Wheel

30 191730

Nut,

Hex

31 404845

Pawl,

Drive

581685301

Wheel & T

ire Assembly

, Rear

409148

Nut, Flangelock 3/8-16

34 404835

Pinion

431138

Wheel Adjuster

, F

ront, RH

431139

Wheel Adjuster

, F

ront, LH

163409

Screw

, Hi-Lo Thread

400246X460

Wheel & T

ire Assembly

, F

ront

55 581351301

Spring,

Return

59 441786X004

Support

Bracket

86 587969201

ulley

, Idler

87 581127601

Screw

Summary of Contents for 944.364701

















Search results

Summary of Contents for 944.364701

Reviews:

Related manuals for 944.364701

Brands by name

Popular brands

Craftsman 944.364701, Owner'S Manual

Search results

Summary of Contents for 944.364701

Reviews:

Related manuals for 944.364701

Brands by name

Popular brands