background image

14

•   If lubricant is required, use only Texaco 

Starplex Pre mi um 1 Grease, Part No. 
750369.  Do not substitute.

ENGINE

LUBRICATION

Use only high quality detergent oil rated 
with API service classifi cation SG–SL.
Select the oil's SAE viscosity grade 
according to your expected operating 
temperature.

5.   Slowly pour oil down the oil fi ll spout, 

stopping every few ounces to check 
the oil level with the dipstick.

6.   Stop adding oil when you reach the 

FULL mark on the dipstick.  Wait a 
minute to allow oil to settle.

7.   Continue adding small amounts of oil, 

rechecking the dipstick until oil level 
settles at FULL.  DO NOT overfi ll, or 
engine will smoke heavily from the 
muffl er on startup.

8.   Always be sure to retighten oil dipstick 

before starting engine.

9.   Re con nect spark plug wire to plug.

AIR FILTER 

Your engine will not run properly and may 
be damaged by using a dirty air fi lter. 
Replace the air fi lter cartridge every 100 
hours of op er a tion or every season, which-
 ev er occurs fi rst.  Service air cleaner more 
often under dusty conditions.

TO CLEAN AIR FILTER
1.   Loosen screw and tilt cover to re move.
2.   Carefully remove cartridge.
3.   Clean by gently tapping on a fl at sur-

face. If very dirty, replace car tridge.

 CAUTION:

  Pe tro leum solvents, such as 

ker o sene, are not to be used to clean car-
 tridge. They may cause de te ri o ra tion of the 
cartridge. Do not oil car tridge. Do not use 
pres sur ized air to clean or dry car tridge.
4.   Install cartridge, then replace cover 

making sure the tabs are aligned with 
the slots in the back plate. Fasten 
screw securely. 

NOTE:

  Although multi-viscosity oils 

(5W30, 10W30 etc.) improve starting in 
cold weather, these multi-viscosity oils will 
result in increased oil consumption when 
used above 32°F. Check your engine oil 
level more frequently to avoid possible 
engine damage from running low on oil.
Change the oil after every 25 hours of 
operation or at least once a year if the 
lawn mower is not used for 25 hours in 
one year.
Check the crankcase oil level before 
starting the engine and after each fi ve (5) 
hours of continuous use. Tighten oil plug 
securely each time you check the oil level.

TO CHANGE ENGINE OIL

NOTE

:  Before tipping lawn mower to drain 

oil, empty fuel tank by running engine until 
fuel tank is empty.
1.   Disconnect spark plug wire from spark 

plug and place wire where it cannot 
come in contact with plug.

2.   Remove engine oil cap; lay aside on a 

clean surface.

3.   Tip lawn mower on its side as shown 

and drain oil into a suitable container. 
Rock lawn mower back and forth to re-
move any oil trapped inside of engine.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20

0

30

40

80

100

-30

-20

0

20

30

40

F
C

32

-10

10

60

5W-30

SAE 30

Container

4.   Wipe off any spilled oil from lawn 

mower or side of engine.

Slots

Lip

Cover 

tabs

Back plate

Cartridge

Cover

MUFFLER

Inspect and replace corroded muffl er as it 
could create a fi re hazard and/or dam age.

SPARK PLUG

Replace spark plug at the beginning of 
each mowing season or after every 100 
hours of operation, whichever occurs 
fi rst.  Spark plug type and gap setting 
are shown in the “PROD UCT SPEC I FI C-
A TIONS” section of this manual.

Summary of Contents for 917.37706





















Reviews: