Craftsman 486.242112 Owner'S Manual Download Page 8

Page: 8 / 16

STEP 14 - ASSEMBLE SUPPORT RODS

IMPORTANT: Do not over bend the support rods
during the following step. Over bending will decrease the
supporting tension of the rods.

• Assemble the two hopper support rods as shown in

ﬁ gure 14. Place the ends of the rods into the holes in
the upper and lower hopper tubes, ﬂ exing the rod just
enough to ﬁ t into the holes in the tubes.

NOTE: The hopper's mesh wind screen is not shown in

ﬁ gure 14 in order to better show the hopper support
rods.

• Fold the bag ﬂ aps around the lower hopper tubes and

attach to the bag bottom using the snaps. See ﬁ gure
13.

FIGURE 13

STEP 13 - ATTACH BAG BOTTOM

• Insert the bag frame strap into the stitched sleeve at

the front edge of the bag bottom. See ﬁ gure 11.

FIGURE 12

FIGURE 14

CLEVIS PIN (N)

HAIR COTTER
PIN (L)

BAG FRAME STRAP

SNAP

FLAP

SUPPORT
RODS

BAG FRAME STRAP

STITCHED
SLEEVE

• Assemble the bag frame strap to the holes in the

lower hopper tubes using two clevis pins (N) and hair
cotter pins (L). See ﬁ gure 12.

FIGURE 11

Summary of Contents for 486.242112

















Search results

Summary of Contents for 486.242112

Reviews:

Related manuals for 486.242112

Brands by name

Popular brands

Craftsman 486.242112, Owner'S Manual

Search results

Summary of Contents for 486.242112

Reviews:

Related manuals for 486.242112

Brands by name

Popular brands