Craftsman 48181 Operator'S Manual Download

Page: 2 / 12

NOTE:

Repeat this

Air Purge Procedure

whenever the jack

displays reduced

lifting performance.

CUSTOMER HELP LINE

Parts and Questions

1-888-332-6419

8:00 AM - 4:45 PM Central Time

Monday- Friday

Jack

AIR PURGE PROCEDURE

IMPORTANT: BEFORE FIRST USE, perform the following Air Purge Procedure to remove any air that may

have been introduced into the hydraulic system as a result of product shipment and handling.

Pump Plunger

Insert Handle

See “ ASSEMBLY” on page 4 to

assemble handle. Loosen handle

socket screw. Insert end of handle

into handle socket. Tighten screw.

Rapidly Pump

Rapidly pump the handle 6 - 8

times. Leave handle in down

position to expose oil fill screw.

Turn Handle

Counterclockwise

Turn handle counterclockwise

two full turns to fully open

release valve.

Screwdriver

Oil Fill Screw

Turn Handle Clockwise

Turn the handle clockwise until it

stops.

READY TO USE

Jack is now ready for use. Check

for proper pump action.

Purge Air

With a flat blade screwdriver,

loosen the oil fill screw

about halfway up to release

trapped air from

the system. Tighten the

screw back down.

Summary of Contents for 48181













Search results

Summary of Contents for 48181

Reviews:

Related manuals for 48181

Brands by name

Popular brands

Craftsman 48181, Operator'S Manual

Search results

Summary of Contents for 48181

Reviews:

Related manuals for 48181

Brands by name

Popular brands