background image

18

Emission Warranty Statement

California / EPA emission control Warranty Statement

The California air resources board, EPA 
(Environmental Protection Agency), and Sears are 
pleased to explain the mission control system warranty 
on your 2000 and later small off-road engine. In 
California and the 49 states, new small off-road engines 
must be designed, built and equipped to meet the 
states stringent anti-smog standards. Sears must 
warrant the emission controls system on your small off-
road engine for the periods of time listed below 
provided there has been no abuse, neglect or improper 
maintenance of your small off-road engine. 

Your emission control system may include parts such 
as the carburetor or fuel-injection system, the ignition 
system, and catalytic converter. Also included may be 
hoses, belts, connectors, and other emission-related 
assemblies.

Where a warrantable condition exists, Sears will repair 
your small off-road engine at no cost to you, including 
diagnosis, parts, and labor.

The 2000 and later small off-road engines are 
warranted for two years. If any emission-related part on 
your engine is defective, the part will be repaired or 
replaced by Sears.

Owner’s Warranty Responsibilities:

As the small off-road engine owner, you are 
responsible for the performance of the required 
maintenance listed in your operator’s manual. Sears 
recommends that you retain all receipts covering 
maintenance on your small off-road engine, but Sears 
cannot deny warranty solely for the lack of receipts or 
for your failure to ensure the performance of all 
scheduled maintenance. 

As the small off-road engine owner, you should 
however be aware that Sears may deny you warranty 
coverage if your small off-road engine or a part has 
failed due to abuse, neglect, improper maintenance or 
unapproved modifications.

You are responsible for presenting your small off-road 
engine to a Sears service center as soon as a problem 
exists. The warranty repairs should be completed in a 
reasonable amount of time, not to exceed 30 days.

Manufacturer’s Warranty Coverage:

The warranty period begins on the date the engine or 
equipment is delivered to the retail purchaser. 

The manufacturer warrants to the initial owner and 
each subsequent purchaser, that the engine is free 
from defects in material and workmanship which cause 
the failure of a warranted part for a period of two years.

Repair or replacement of warranted part will be 
performed at no charge to the owner at a Sears service 
center. 

Any warranty part which is not scheduled for 
replacement, as required maintenance or which is 
scheduled only for regular inspection to the effect of 
“repair or replace as necessary” is warranted for the 
warranty period. Any warranted part which is scheduled 
for replacement as required maintenance will be 
warranted for the period of time up to the first scheduled 
replacement point for that part.

The owner will not be charged for diagnostic labor 
which leads to the determination that a warranted part 
is defective, if the diagnostic work is performed at a 
Sears service center. 

The manufacturer is liable for damages to other engine 
components caused by the failure of a warranted part 
still under warranty.

Failures caused by abuse, neglect, or improper 
maintenance are not covered under warranty.

The use of add-on or modified parts can be grounds for 
disallowing a warranty claim. The manufacturer is not 
liable to cover failures of warranted parts caused by the 
use of add-on or modified parts.

In order to file a claim, go to your nearest Sears service 
center. Warranty services or repairs will be provided at 
all authorized Sears service centers.

Any manufacturer approved replacement part may be 
used in the performance of any warranty maintenance 
or repair of emission related parts and will be provided 
without charge to the owner. Any replacement part that 
is equivalent in performance or durability may be used 
in non-warranty maintenance or repair and will not 
reduce the warranty obligations of the manufacturer. 

The following components are components are 
included in the emission related warranty of the engine 
air filter, carburetor, primer, fuel lines, fuel pick up/fuel 
filter, ignition module, spark plug and muffler.     

Summary of Contents for 316.29270





































Reviews: