background image

3

SAFETY INSTRUCTIONS

training

Read, understand, and follow all instructions on the machine and 

• 

in the manual(s) before attempting to assemble and operate. 
Keep this manual in a safe place for future and regular reference 
and for ordering replacement parts. 
Read the Operator’s Manual and follow all warnings and safety 

• 

instructions. Failure to do so can result in serious injury to the 
operator and/or bystanders. For questions call, 1-800-659-5917.
Be familiar with all controls and their proper operation. Know how 

• 

to stop the machine and disengage them quickly.
Never allow children under 14 years of age to operate this 

• 

machine. Children 14 and over should read and understand the 
instructions and safe operation practices in this manual and on 
the machine and be trained and supervised by an adult. 
Never allow adults to operate this machine without proper 

• 

instruction. 
Thrown objects can cause serious personal injury. Plan your 

• 

snow-throwing pattern to avoid discharge of material toward 
roads, bystanders and the like. 
Keep bystanders, pets and children at least 75 feet from the 

• 

machine while it is in operation. Stop machine if anyone enters 
the area.
Exercise caution to avoid slipping or falling, especially when 

• 

operating in reverse.

PreParation

Thoroughly inspect the area where the equipment is to be used. 
Remove all doormats, newspapers, sleds, boards, wires and other 
foreign objects, which could be tripped over or thrown by the auger/
impeller. 

Always wear safety glasses or eye shields during operation and 

• 

while performing an adjustment or repair to protect your eyes. 
Thrown objects which ricochet can cause serious injury to the 
eyes.
Do not operate without wearing adequate winter outer garments. 

• 

Do not wear jewelry, long scarves or other loose clothing, which 
could become entangled in moving parts. Wear footwear which 
will improve footing on slippery surfaces. 
Use a grounded three-wire extension cord and receptacle for all 

• 

machines with electric start engines. 
Adjust collector housing height to clear gravel or crushed rock 

• 

surfaces. 
Disengage all control levers before starting the engine. 

• 

Never attempt to make any adjustments while engine is running, 

• 

except where specifically recommended in the operator’s manual.
Let engine and machine adjust to outdoor temperature before 

• 

starting to clear snow. 

Warning

CaLifornia ProPosition 65

Engine Exhaust, some of its constituents, and certain vehicle 
components contain or emit chemicals known to State of California 
to cause cancer and birth defects or other reproductive harm.

Warning

Your Responsibility

—Restrict the use of this power machine to 

persons who read, understand and follow the warnings and instruc-
tions in this manual and on the machine. 

saVe tHese instrUCtions!

Warning

This symbol points out important safety instructions which, if not 
followed, could endanger the personal safety and/or property of 
yourself and others. Read and follow all instructions in this manual 
before attempting to operate this machine. Failure to comply with 
these instructions may result in personal injury. When you see this 
symbol, HEED ITS WARNING!

danger

This machine was built to be operated according to the safe opera-
tion practices in this manual. As with any type of power equipment, 
carelessness or error on the part of the operator can result in serious 
injury. This machine is capable of amputating fingers, hands, toes 
and feet and throwing debris. Failure to observe the following safety 
instructions could result in serious injury or death.

Summary of Contents for 247.88955





































































Reviews: