background image

page  9

Troubleshooting.

Problem: 

Fan fails to operate.

Solutions:

1. Check power to fan.
2. Verify that reverse switch is set completely in 
either direction.
3. Check to be sure fan is wired properly.

Problem: 

Light kit not lighting.

Solutions:

1. Check power to fan.
2. Check that bulbs are installed correctly.
3. Check to be sure wires in canopy are wired 
properly.

Problem: 

Fan operates but lights fail.

Solutions: 

1. Check that bulbs are installed correctly.
2. Check to be sure wires in canopy are wired 
properly.
3. Replace defective bulbs with same type of bulb.

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit in one of the hardware 
packs. 

If no blade balancing kit is provided, please 

call Customer Support, 1-800-486-4892, to request 
one.

2. Check to be sure set screw(s) on motor housing 
yoke is (are) tightened securely.
3. Check to be sure set screw on hanging ball is 
tightened securely.

WARNING: 

Failure to disconnect power supply 

prior to troubleshooting any wiring issues may 
result in serious injury.

JMLI1809

Warranty.

CRAFTMADE™ LIFETIME LIMITED WARRANTY:
CRAFTMADE warrants this fan to the original household 
purchaser for indoor use under the following provisions:
1-YEAR WARRANTY: CRAFTMADE will replace or repair any 
fan which has faulty performance due to a defect in 
material or workmanship. Contact Craftmade Customer 
Service at 

1-800-486-4892 

to arrange for return of fan. 

Return fan, shipping prepaid, to Craftmade.  We will repair 
or ship you a replacement fan, and we will pay the return 
shipping cost.
5-YEAR WARRANTY: CRAFTMADE will repair or replace, at  
no charge to the original purchaser, any fan motor that fails 
to operate satisfactorily when failure results from normal 
use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Craftmade 
Industries. We will repair or ship purchaser a replacement 
motor and Craftmade will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: CRAFTMADE will 
repair the fan, at no charge for labor only to the original 
purchaser, if the fan motor fails to operate satisfactorily 
when failure results from normal use. Parts used in the 
repair will be billed to the purchaser at prevailing prices at 
time of repair.
    The purchaser shall be responsible for all costs incurred 
in the removal, reinstallation and shipping of the product 
for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results in 
causing the malfunction. Deterioration of finishes or other 
parts due to time or exposure to salt air is specifically 
exempted under this warranty.
    Neither Craftmade nor the manufacturer will assume any 
liability resulting from improper installation or use of this 
product. In no case shall the company be liable for any 
consequential damages for breach of this, or any other 
warranty expressed or implied whatsoever. This limitation 
as to consequential damages shall not apply in states 
where prohibited.

Parts Replacement.

For parts and information, please refer to
"Parts Inventory" on page 2.
Craftmade Customer Support:

1-800-486-4892

www.craftmade.com

Summary of Contents for NIK52





















Reviews: