Craftex CT174 User Manual Download Page 2

Page: 2 / 20

TABLE OF CONTENTS

General Safety Instructions ..........................................................................3

Specific Safety Instructions...........................................................................4

CT174 Features............................................................................................5

Physical Features .........................................................................................6

Unpacking ....................................................................................................7

Proper Grounding .........................................................................................7

Installing the Sanding Disc ...........................................................................8

Installing the Sanding Belt ............................................................................8

Belt Tracking Adjustment..............................................................................9

Installing the Dust Ports................................................................................10

Installing the Work Table ..............................................................................10

Installing the Back Stop ................................................................................11

On/Off Switch ...............................................................................................11

Test Run .......................................................................................................12

Work-Piece Inspection..................................................................................12

Adjusting the Work Table Tilt........................................................................13

Sanding Tips.................................................................................................13

Horizontal/Vertical Sanding ..........................................................................13

Adjusting the Miter Gauge ............................................................................14

Maintenance .................................................................................................15

V-Belt Tension & Replacement.....................................................................15

Troubleshooting............................................................................................17

Parts Breakdown ..........................................................................................18

Parts List ......................................................................................................19

Warranty .......................................................................................................20

Summary of Contents for CT174





















Search results

Summary of Contents for CT174

Reviews:

Related manuals for CT174

Brands by name

Popular brands

Craftex CT174, User Manual

Search results

Summary of Contents for CT174

Reviews:

Related manuals for CT174

Brands by name

Popular brands