CPE CPE 46599 Owner'S Manual & Operating Instructions Download Page 13

REV 46599-20120703  

10

46599

 

ENGLISH

Add fuel Cont’d.

Add fuel

1 .  Use clean, fresh, regular unleaded fuel with a 

minimum octane rating of 85 and an ethanol content 
of less than 10% by volume .

2 .  DO NOT mix oil with fuel .
3 .  Clean the area around the fuel cap . 
4 .  Remove the fuel cap .
5 .  Slowly add fuel to the tank . DO NOT overfill . Allow 

approximately ¼ inch of space for fuel expansion .

6 .  Screw on the fuel cap and wipe away any spilled fuel .

ASSEMBLy

Grounding

Your generator must be properly connected to an 
appropriate ground to help prevent electric shock .

A ground terminal connected to the frame of the generator 
has been provided on the power panel . For remote 
grounding, connect of a length of heavy gauge  
(12 AWG minimum) copper wire between the generator 
ground terminal and a copper rod driven into the ground . 
We strongly recommend that you consult with a qualified 
electrician to ensure compliance with local electrical codes .

Failure to properly ground the generator can result 
in electric shock .

WARNING

Use regular unleaded gasoline with a minimum 
octane rating of 85 .

Do not mix oil and gasoline .
Fill tank to approximately ¼” below the top of the 
tank to allow for fuel expansion .
DO NOT pump gas directly into the generator at the 
gas station . Use an approved container to transfer 
the fuel to the generator .
DO NOT fill fuel tank indoors .
DO NOT fill fuel tank when the engine is running or hot .
DO NOT overfill the fuel tank .
DO NOT light cigarettes or smoke when filling the 
fuel tank .

CAUTION

Pouring fuel too fast through the fuel screen may 
result in blow back of fuel at the operator while filling .

WARNING

Our engines work well with 10% or less ethanol 
blend fuels . When using blended fuels there are 
some issues worth noting: 

 

– Ethanol-gasoline blends can absorb more water 

than gasoline alone . 

 

– These blends can eventually separate, leaving 

water or a watery goo in the tank, fuel valve and 
carburetor . 

 

– With gravity-fed fuel supplies, this compromised 

fuel can be drawn into the carburetor and cause 
damage to the engine and/or potential hazards . 

 

– There are only a few suppliers of fuel stabilizer 

that are formulated to work with ethanol blend 
fuels .

 

– Any damages or hazards caused by using 

improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not 
covered by manufacture’s warranty . 

It is advisable to always shut off the fuel supply, 
run the engine to fuel starvation and drain the tank 
when the equipment is not in use for more than 30 
days .

NOTE

Summary of Contents for CPE 46599































Reviews: