background image

TABLE A

Warranty for gas appliance heat exchangers only.

           Product

        Warranty Period

Cozy Gas Fired Floor Furnace

10 Years

Cozy Gas Fired Wall Furnace

10 Years

Cozy Gas Fired Vented Console Heater

10 Years

Cozy Gas Fired Direct Vent Heater

10 Years

Cozy Gas Fired Counterflow Furnace

10 Years

Cozy Gas Fired Counterflow Direct Vent Furnace

10 Years

Cozy Gas Fired Mobile Home Direct Vent Furnace

10 Years

Cozy Gas Fired Hi-Efficient Direct Vent Wall Furnace

10 Years

LOUISVILLE TIN AND STOVE COMPANY

P.O. BOX 2767     -     LOUISVILLE, KY. 40201-2767

LIMITED WARRANTY

The Louisville Tin & Stove Co. warrants to the

original user the accompanying product for the period
specified herein, provided said product is installed,
operated, maintained, serviced, and used according to
the instructions and specifications accompanying the
product.   AS OUTLINED IN OUR INSTRUCTIONS,
ANY WARRANTY CONSIDERATIONS ARE
CONTINGENT ON INSTALLATION BY A
QUALIFIED INSTALLER (CONTRACTOR).
SELF-INSTALLATION IS NOT RECOMMENDED
AND MY INVALIDATE YOUR WARRANTY.

If within a period of one year from the date of

installation of the product, any part supplied by the
manufacturer proves to be defective due to workmanship
or material, it will replace such part, provided parts have
not been subjected to misuse, alteration, neglect, or
accidents.  The term of the warranty for the heat exchanger
is covered in Table A below.  Any claim not made within
ten (10) days after the expiration of the warranty period
shall be deemed waived by the user.

The manufacturer shall have no liability or be

required to perform any obligation under this warranty
unless, when requested, the user returns, at the user’s
expense, the component or product claimed defective, to
the manufacturer for inspection, to enable the
manufacturer to determine if the claimed defect is covered
by this warranty.

No charges for freight, labor or other expenses

incurred in the repair, removal, or replacement of any
product or component claimed to be defective, will be paid
by the manufacturer to the user, and the manufacturer will
not be liable for any expenses incurred, by the user, in
remedying any defect in the product.

Service under this warranty is the responsibility

of the installer.  In the event service under this warranty is
needed, the user of the product shall request such service

directly from the installer.  If the user is unable to locate
the installer, the  user  should write directly  to  the
manufacturer, and the name of an alternative service source
will be supplied.

The product safety registration card (packed

inside the appliance) must be completed and returned to
the factory.

THIS WARRANTY IS EXPRESSLY IN LIEU

OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED (WHETHER WRITTEN OR ORAL).  ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR OF
FITNESS FOR A PARTICULAR PURPOSE IS
EXPRESSLY LIMITED TO THE DURATION OF THE
MANUFACTURER’S EXPRESS, WRITTEN
WARRANTY.

UNDER NO CIRCUMSTANCES SHALL THE

MANUFACTURER BE LIABLE FOR ANY SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMANGES OR
EXPENSES ARISING DIRECTLY OR INDIRECTLY
FROM ANY COMPONENT OR FROM THE USE
THEREOF.  THE REMEDIES SET FORTH HEREIN
SHALL BE THE EXCLUSIVE REMEDIES AVAILABLE
TO THE USER AND ARE IN LIEU OF ALL OTHER
REMEDIES.

SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS
MAY NOT APLY TO YOU.

SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY, FROM STATE TO STATE.

Summary of Contents for W251F and





















Reviews: