background image

5

Important Safety Rules

WARNING

7.) Breathing hazard.

Poisonous fumes from engine can kill you. Do not operate indoors even if

Ventilated. For outdoor use only.

CAUTION

1.) Hot muffler.

You can be burned by muffler.
Do not touch.

Save These Instructions

6.) Risk of fire and explosion.

- Hot exhaust fumes from engine can cause fire. Gasoline is highly flammable 

and explosive. You can be burned or seriously injured when handling fuel.
- Position muffler at least 7 feet from combustible objects.
- Before adding fuel, stop the engine and keep heat, sparks, and flame away.
- Do not add fuel when engine is running or still hot. No smoking near engine.
- Do notpump fuel directly into engine at gas station. Static charge can 

buildand ignite fuel. Use a UL approved fuel container to transfer gas to 

theengine. Wipe up fuel spills immediately.
- Only store and handle fuel outdoors. Gasoline vapors can ignite if theycollect 

inside an enclosure. Explosion can result.
- Do not change or add to exhaust system. Fire can result.
- Do not change or add fuel tanks or fuel lines. Fire can result.
- Before each use, check fuel tank and fuel lines for leaks. Any fuel leak is a 

fire hazard. Fix any fuel leaks before starting engine.
- During transportation take precautions to make sure machine will not tip over 

and cause a fuel leak fire hazard.

Summary of Contents for l2T



















Reviews: