Safety 2
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation, operation, and maintenance of the product.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential
for personal injury!
indicates a hazard which, if not avoided, will
result in death or serious injury.
indicates a hazard which, if not avoided,
could result in death or serious injury.
indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE addresses practices not related to
personal injury.
Carefully read and follow all safety instructions in this
manual and on pump .
Keep safety labels in good condition. Replace missing or
damaged safety labels.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
1. To avoid risk of serious bodily injury and property
damage, read the safety instructions carefully before
installing this pump.
2. Follow local and/or national plumbing and electrical
codes when installing the pump.
3.
Risk of fire and explosion . Can cause
severe injury, property damage or death. To avoid
risk of fire and explosion, Pump water only with this
pump. Do not use this pump in an atmosphere that
might contain flammable fumes or vapors.
4.
Risk of burns . If water is trapped in the
pump during operation it may turn to steam. Trapped
steam can lead to explosion and burns. Never run
the pump with the outlet closed or obstructed.
5.
Risk of explosion . Do not ground to
a gas supply line. The pump body may explode if
used as a booster pump unless a relief valve capable
of passing the full pump flow at 60 PSI (414 kPa)
is installed. Never run the pump dry. To do so can
damage internal parts, overheat pump (which can
cause burns to people handling or servicing pump),
and will void warranty!
6.
Risk of burns . Motors are designed to
operate at high temperatures. To avoid burns when
servicing pump, allow it to cool for 20 minutes after
shut-down before handling.
7. If used with a well for potable water, always
disinfect the well and test the water for purity before
using. Check with your local health department for
testing procedures.
8. Complete pump and piping must be protected
against freezing. Freezing will cause damage and
void the warranty.
9. This pump is not designed, nor intended, for the
pumping of chemicals or corrosive liquids. Pump
water only with this pump.
10. Do not run pump dry. If the pump is dry, damage
will result and void the warranty.
11.
Risk of electric shock . Can shock, burn
or kill.
• The pump is supplied with a 3-conductor grounding
type cord. Connect only to a properly grounded,
GFCI protected outlet. Do not lift the pump by the
electrical cord.
Match the motor voltage and the power supply
voltage. The supply voltage must be /- 10%
of the motor nameplate voltage. Incorrect voltage
can cause fire or seriously damage the motor
and will void the warranty. If in doubt, consult a
licensed electrician.
• The pump is non-submersible. Keep the motor dry at
all times. Do not wash the motor. Do not immerse.
Protect the motor from wet weather.
• If using an extension cord, use only a UL approved
indoor/outdoor, 3-wire, grounding type cord. Do not
allow any part of the cord or the receptacle ends to
sit in water or in damp locations.
• Unplug the pump before servicing. To avoid
fatal shocks, proceed as follows if the pump
needs servicing.
A. Disconnect the power to the pump outlet box
before pulling the pump plug.
B. Take extreme care when changing fuses. To
reduce the chance of fatal electrical shocks, DO
NOT stand in water or put your finger in the
fuse socket.
C. Ground the pressure switch or motor before
before running this pump.
D. Plug pump into a Ground Fault Circuit
Interrupter (GFCI) protected grounded
outlet only.
Summary of Contents for CLSS5
Page 16: ......
