background image

Ussc 

7

INSTALLATION

SAFETY NOTICE

•  IF  THIS  STOVE  IS  NOT  PROPERLY  INSTALLED,  A  HOUSE  FIRE  MAY  RESULT.  TO  

REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. 

•  CONSULT  YOUR  MUNICIPAL  BUILDING  DEPARTMENT  OR  FIRE  OFFICIALS  ABOUT 

PERMITS, RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA.

•  USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED.
•  KEEP FURNITURE AND DRAPES WELL AWAY FROM THE STOVE.
•  NEVER  USE  GASOLINE,  GASOLINE-TYPE  LANTERN  FUEL,  KEROSENE,  CHARCOAL 

LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS 

HEATER. KEEP  ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS IN 

USE.

•  IN  THE  EVENT  OF  A  CHIMNEY  FIRE,  PUSH  THE  AIR  CONTROL  FULL  CLOSED  TO  

DEPRIVE THE FIRE OF OXYGEN. CALL THE FIRE DEPARTMENT.

•  DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
•  A SOURCE OF FRESH AIR INTO THE ROOM OR SPACE HEATED SHALL BE PROVIDED 

WHEN REQUIRED.

POSITIONING THE STOVE

It is very important to position the wood stove as close as possible to the chimney, and in an area 

that will favor the most efficient heat distribution possible throughout the house.  The stove must 

therefore be installed in the room where the most time is spent, and in the most spacious room 

possible.  Recall that wood stoves produce radiating heat, the heat we feel when we are close to a 

wood stove. A wood stove also functions by convection, that is through the displacement of hot air 

accelerated upwards and its replacement with cooler air. If necessary, the hot air distribution from 

the stove may be facilitated by the installation of a blower.

The wood stove must not be hooked up to a hot air distribution system since an excessive 

accumulation of heat may occur.
A wood stove must never be installed in a hallway or near a staircase, since it may block the 

way in case of fire or fail to respect required clearances.

Summary of Contents for 2000

























Reviews: