background image

Version 1.0b 

22 

 

MAINTENANCE INSTRUCTIONS 

The frequency of performing Inglenook fireplace maintenance depends on site-specific conditions and the 
frequency of use.  Country Flame recommends that a certified service technician perform an annual check-
up prior to the start of each heating season.  Both specific and general maintenance guidelines are presented 
in this section.  If there are any questions about maintenance or proper service, contact a local authorized 
dealer, a certified service technician, or Country Flame direct for additional clarification.  

IMPORTANT: 

TURN OFF INGLENOOK POWER AND SHUT OFF THE GAS BEFORE SERVICING. 

 

SPECIFIC TASKS 

CLEANING BURNERS AND CONTROLS 
FREQUENCY:  

Once during annual inspection. 

PERFORMED BY: 

 

Qualified service technician. 

TASK PERFORMED: 

Clean the control compartment.  Remove and clean logs (careful not to 
damage ceramic logs).  While logs are removed, clean and inspect 2 
burners, inspect and clean pilot assembly, and inspect and clean 
surrounding burner area. 

 

REPLACE OLD EMBERS 
FREQUENCY:  

Once during annual inspection. 

PERFORMED BY: 

 

Qualified service technician. 

TASK PERFORMED: 

Replace ember material with new ember material.  Additional ember 
material can be purchased from a local authorized Country Flame Dealer.  
(Only use genuine Country Flame ember material) 

 

CHECK FLAME AND PILOT 
FREQUENCY:  

Periodically.

 

PERFORMED BY: 

 

Qualified service technician or homeowner. 

TASK PERFORMED: 

Visually inspect the burner’s flame height and burn patterns.  The front and 
rear burner flames are steady and not lifting or floating away from the 
burner surfaces.  Refer to FIGURE 5d for a picture representation of the 
proper flame with logs and embers installed.  Visually inspect that the pilot 
light is burning with four blue flame nodes as shown in FIGURE 22, 
protruding from the pilot flame diffuser.  No sputter or blockage of any 
pilot flame or its four nodes should be visible.  If there is any abnormality 
observed in a flame pattern, contact a local authorized dealer or a certified 
technician.

 

 

FIGURE 22:  STANDING PILOT 

Summary of Contents for INGLS 24-N



































Reviews: