background image

 

4

7. 

DO NOT MOVE CONTROL LEVER(S)

 

from forward position to reverse position 
rapidly.  The speed and/or direction of 
travel is affected instantly by movement 
of the Control Lever(s). 

 

8. 

DO NOT ALLOW CHILDREN TO 
OPERATE MOWER.

  Do not allow 

others who have not had instruction to 
operate mower. 

 

9. 

ALWAYS TURN ENGINE OFF AND 
REMOVE KEY

 before leaving the 

mower to prevent children and 
inexperienced operators from starting 
the engine.  Never leave the mower 
unattended with engine running.  Always 
wait for all moving parts and all sounds 
to stop before leaving operator’s seat. 

 

10. 

WEAR STURDY, ROUGH-SOLED 
WORK SHOES AND CLOSE-FITTING 
SLACKS AND SHIRTS.

  Never operate 

mower in bare feet, sandals or 
sneakers. 

 

11. 

KNOW THE AREA YOU ARE TO 
MOW.

  Watch for hidden danger such 

as rocks, roots, sticks, holes, bumps, 
and drop-offs, etc.  Before mowing, pick 
up all debris in area to be mowed.  
Sharp and hard objects can be 
propelled at a high speed and can act 
like shrapnel.  Walk through tall grass 
BEFORE MOWING to make sure there 
are no hidden dangers.  Mow higher 
than desired in tall grass to expose any 
hidden objects and/or obstacles, clean 
the area, and then mow to the desired 
height. 

 

12. 

NEVER REFUEL A MOWER 
INDOORS.

  Allow the engine time to 

cool before refueling.  Unseen vapors 
may be ignited by a spark.  Always 
clean up spilled gasoline.  Never run the 
engine indoors in a garage or any other 
closed building.  Allow engine to cool 
before storing in any enclosure.  The 
engine exhaust and gasoline fumes are 
dangerous. 

 
13. 

DISENGAGE BLADES BEFORE 
DRIVING ACROSS WALKS

 or 

projecting objects. 

 
14. 

NEVER REMOVE THE FUEL CAP

 or 

add gasoline to a running or hot engine 
that has not been allowed to cool for 

several minutes after running.  Always 
make sure the gas cap is in place. 

 

15. 

NEVER CARRY PASSENGERS.

 

 

16. 

DO NOT SMOKE AROUND THE 
MOWER

 or the gasoline storage 

container.  Gasoline fumes can easily 
ignite. 

 

17. 

KEEP GASOLINE IN A WELL-
VENTILATED AREA

 away from your 

living quarters and in tightly-capped 
safety cans.  Never store mower with 
gasoline in the tank inside a building 
where fumes may reach open flame or 
spark. 

 

18. 

DISENGAGE BLADES, STOP ENGINE 
AND REMOVE IGNITION KEY

 before 

any servicing.  Be sure all moving parts 
and all sounds have stopped.  Let 
engine cool and disconnect the spark 
plugs so the engine cannot start by 
accident.  A SLIGHT ROTATION OF 
THE BLADES COULD START THE 
ENGINE. 

 

19. 

KEEP ALL NUTS, BOLTS, AND 
SCREWS TIGHT

 to be sure equipment 

is in safe working condition, especially 
blade mounting bolts. 

 

20. 

VEHICLE SHOULD BE STOPPED 
AND INSPECTED FOR DAMAGE

 after 

striking a foreign object and the damage 
should be repaired before restarting and 
operating the equipment.  Stop 
immediately and check for damage or 
loose parts if mower should start 
vibrating. 

 

21 

KEEP SAFETY DEVICES AND 
GUARDS IN PLACE.

  If any of the 

safety switches become inoperable, 
have them repaired immediately. 

 

22. 

DO NOT STEP OR STAND ON THE 
MOWER HOUSING.

  Step or stand only 

on the foot deck. 

 

23. 

WATCH OUT FOR TRAFFIC

 near 

roadways and when crossing roads. 

 

24. 

DO NOT USE MOWER WHEN GRASS 
IS WET OR SLIPPERY. 

 
25. 

MOW ONLY DURING DAYLIGHT.

 

 

Summary of Contents for Zero Turn Radius Mower


























Reviews: