Country Clipper AVENUE 150/A100 Safety Instruction & Operatorrs Manual Download Page 9

  8 

 

     

CAUTION

      

 

AVOID HILLS AND SLOPES.  USE EXTREME 

CAUTION WHEN MOWING UP OR DOWN 

SLOPES.  NEVER MOW ACROSS THE FACE 

OF A SLOPE.  IF A SLOPE MUST BE 

ASCENDED, BACK UP THE SLOPE; DRIVE 

FORWARD WHEN DESCENDING. 

 

13. TO STOP:

 

 

A. 

   Move Joystick Control Lever to neutral 

position and then to the “DOWN” 
position. 

B. 

   Disengage the mower blade clutch by 

moving the clutch to the “OFF” 
position. 

C. 

   Set the parking brake. 

D. 

   Turn ignition key to “OFF” position. 

E. 

   Remove the key and wait for all 

movement and sound to cease before 
dismounting. 

 

     

CAUTION

      

 

WHEN LEAVING THE MOWER 

UNATTENDED, ALWAYS REMOVE THE KEY 

AND SET THE PARKING BRAKE, EVEN IF 

JUST FOR A FEW MOMENTS.  HELP 

PROTECT CHILDREN AND OTHER 

UNAUTHORIZED PERSONS FROM 

ACCIDENTS. 

 
 
 

OPERATION  

FREE WHEEL 

 

1.  TO FREE WHEEL: 

A. 

Unlock Transmission: Pull the 
Transmission Release Chain out away 
from the Hydrostatic Drive Axle and then 
over into the retaining slot (each side 
must individually be pulled out and over 
into the retaining slot).     

B. 

To re-engage the transmissions push 
the Transmission Release Chain out of 
the retaining slot.  

Transmission Release Chains are 
located on the rear side of the 
Hydrostatic Drive Axles and below the 
Engine Mounting Plate. 

 
 

 

 
 
 
 
 
 
NOTE:  The tractor should never be pulled at 

more than 2 miles per hour or for any 
appreciable distance. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Transmission 

Release Chain 

Retaining Slot 

Summary of Contents for AVENUE 150/A100































Reviews: