Coulomb Technologies ChargePoint CT500-DSTAND Installation Manual Download Page 21

A-1

Appendix A: Limited Product Warranty

COULOMB TECHNOLOGIES INC.
LIMITED PRODUCT WARRANTY

This Limited Product Warranty applies to you, a customer who has purchased COULOMB’s ChargePoint™ Networked Charging 
Stations and/or related products (“

Products

”) from COULOMB TECHNOLOGIES, INC. (“

COULOMB

”) or one of its authorized 

distributors and not for resale. 

LIMITED ONE-YEAR WARRANTY

Subject to the exclusions from warranty coverage set forth below, COULOMB warrants that the Product will be free from any 
defects in materials and/or workmanship (the “

Limited Warranty

”) for a period of one (1) year after the date of the initial 

installation of the Product (the “

One-Year Warranty Period

”). If the Product becomes defective in breach of the Limited Warranty, 

COULOMB will, upon written notice of the defect received during the One-Year Warranty period, either repair or replace, at 
Coulomb’s election, the Product if it proves to be defective; 

provided

, that COULOMB will not be responsible for the cost of any 

labor associated with the repair or replacement of any defective Product.

FIVE-YEAR EXTENDED WARRANTY (Additional Charge Applies)

Subject to the exclusions from warranty coverage set forth below, if you have purchased a five (5) year extended warranty 
(“

Five-Year Extended Warranty

”), and if the Product becomes defective in breach of the Limited Warranty above at any time 

during the five (5) year period after the date of the initial installation of the Product (the “

Five-Year Warranty Period

”), COULOMB 

will, upon written notice of the defect received during the Five-Year Warranty Period, either repair, provide replacement parts for 
the defective parts of the Product or replace the Product, at Coulomb’s election, if it proves to be defective; 

provided

, that 

COULOMB will not be responsible for the cost of any labor associated with the repair or replacement of any defective Product.

COULOMB’s OPTIONS

You acknowledge that replacement products provided by Coulomb under each of the Limited Warranty and the Five-Year 
Extended Warranty may be remanufactured or reconditioned Products or, if the exact Product is no longer manufactured by 
COULOMB, a Product with substantially similar functionality (“

Replacement Products

”). Any Replacement Products so furnished 

will be warranted for the remainder of the original Warranty Period or ninety (90) days from the date of delivery of such 
Replacement Product, whichever is greater. Should COULOMB be unable to repair or replace the Product, COULOMB will refund 
the purchase price of the Product.

EXCLUSIONS FROM LIMITED WARRANTY AND FIVE-YEAR EXTENDED WARRANTY

IMPORTANT: The Limited Warranty and, if purchased, the Five Year Extended Warranty on your Product shall not apply to defects, 
or service repairs, resulting from any of the following:

Alteration or modification of the Product in any way not approved in writing by COULOMB.

Vandalism, abuse, damage or otherwise being subjected to problems caused by negligence (including but not limited to 
physical damage from being struck by a vehicle) or misapplication, or use of the Products other than as specified in the 
applicable COULOMB documentation.

Installation or relocation of the Products unless performed by COULOMB or by a Coulomb authorized installer or service 
provider.

Improper site preparation or maintenance.

Damage as a result of accidents, extreme power surge, extreme electromagnetic field, acts of nature or other causes beyond 
the control of COULOMB.

Use of the Product with software, interfacing, parts or supplies not supplied by COULOMB.

You are responsible for the proper installation and maintenance of the Product. Any service or repairs beyond the scope of the 
Limited Warranty or the Five-Year Extended Warranty above are subject to COULOMB’s then prevailing current labor rates and 
other applicable charges.

Summary of Contents for ChargePoint CT500-DSTAND



























Reviews: