Costco 1902258, Assembly / Care & Use Instructions

Page: 14 / 48

FOR LIQUID PROPANE GAS UNITS
*Do not attempt to disconnect the gas regulator or any gas fitting while your fire pit is in operation.
*A dented or rusty liquid propane cylinder may be hazardous and should be checked by your gas supplier prior to use.
*Do not use a liquid propane cylinder with a damaged valve and any other worn out parts.
*Transit and store the empty gas cylinders carefully and properly.
*If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder;
1. Turn off the gas supply and get away from the gas cylinder and the fire pit at once.
2. Do not attempt to correct the problem yourself.
3. Get to your gas supplier and/or the fire department for help.
WARNING
This screen must be clear and free of obstructions
at all times to insure proper operation.
Screen
DO NOT PLACE GLASS BEADS
ON THE SCREEN. KEEP
SCREEN CLEAR.
CAUTION: Children and adults should be alerted to the hazards on high surface temperatures and should stay away to avoid
burns or clothing ignition. Young children should be carefully supervised when they are in the area of the appliance.
WARNING: Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect
the appliance and to replace any part of control system and any gas control, which has been under water.
SAFETY WARNINGS
1. Never leave the Fire Pit unattended during operation.
2. Clothing or other flammable materials should not be place on or near the appliance.
3. Any guard or other protective device removed for servicing the appliance must be replace d prior to operating the appliance.
4. Installation and repair should be done by a qualified service person. The appliance should b e inspected before use and at least
annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative the control
compartment, burners and circulating air passageways of the appliance be kept clean.
5. Inspect the fuel supply connection before each use of the appliance.
WARNING
1.This appliance is hot when operated and can cause sever burns if contacted.
2. Do not burn any solid fuels in this appliance.
Made in China
14/16
LIGHTING
1. Make sure all labels, packaging and protective films have been removed
from the outdoor fireplace.
3. Check for obstructions of airflow to the burner. Spiders, insects and webs
can clog the burner/venturi tube. A clogged burner tube can lead to a fire.
4. Control knob must be in the “ OFF” position (Figure 3)
5. Clear small area of glass rocks away from the igniter cover (Figure 4).
6. Connect LP gas tank per “Installing LP Gas Tank” section.
7. Turn LP gas tank valve to “OPEN”.
8. Push and hold the electronic igniter to create sparks within the electrode,
continue to hold.
9. Push in the control knob and turn to the “ON” position, Keep holding down the
control knob to allow gas to flow for 20 seconds.
10. After 20 seconds, release and turn control knob counterclockwise to adjust
flame to desired height.
11. If ignition does not occur in 20 seconds turn burner control knob to “ OFF”
wait 5 minutes, fan with a newspaper or magazine, and repeat lighting
procedure.
2. Remove cover and lid from outdoor fireplace before lighting.
12. If igniter does not light burner :
a. Wearing heat-resistant gloves, position a long lit match or long lit butane
lighter near the pilot housing.
c. Remove match/lighter once burner is lit.
TURNING OFF
1. Turn LP gas tank valve to “ CLOSED”.
2. Turn control knob to the “ OFF” position. Note: A “poof” sound is normal as the
last of the LP gas is burned.
3. Disconnect LP gas tank per “Disconnecting LP Gas Tank” section.
b. Push and turn control knob to on.
6. Temporary storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply
(Natural or L.P. gas line).