background image

CARE INSTRUCTIONS: 

Do not use polishes or cleaners on your lamp.  

Unplug lamp, clean with a soft dry cloth.  

Remove plastic cover from the shade before use. 

Clean shade with soft dry cloth.  

 
IF LAMP USED WITH LED: 

 

This device complies with Part 15 of the FCC Rules.

 Operations is subject to the 

following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation. 

 
CAUTION:

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if 

not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one or more of the following measures: 

-- Reorient or relocate the receiving antenna. 

-- Increase the separation between the equipment and receiver. 

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

-- Consult the dealer or an experienced radio/TV technician for help. 

 

 

Made in China / Fabriqué en Chine / Hecho en China

  

                      

 

Summary of Contents for 1288435







Reviews: