background image

 WARNING

 WARNING

Burner

 

knob

 

settings

Operating Your Cooktop

Selecting the Cookware

• To avoid burns and scalding, always turn pan handles

to a position where they cannot be easily hit. Also,

handles should not extend over adjacent burners.

Always set utensils gently onto the grates and center

them so that they are well-balanced.

• Do not drag cookware across the grates. Sliding may

damage the finish. Lift utensils to reposition them. Do

not drop them on the grate.

• Cookware with rough bottoms can cause permanent

damage to the coated surfaces on the grates.

• To avoid burns or a fire hazard, reduce the flame level

if it extends beyond the bottom of the utensil. Flames

extending up the sides are potentially dangerous.

For overall safety and best cooktop performance,

select the correct cooking utensil for the food being

cooked. Improperly selected cooking utensils will

not cook evenly or efficiently.

Use cookware that:

• Has flat, smooth bottoms.

• Is well balanced.

• Has tight fitting lids to keep heat, odors and steam in.

IMPORTANT:

 Avoid spills as much as possible.

The porcelain surfaces of the grates, spill trays and

burner caps are acid-resistant but not acid-proof.

Some foods can cause permanent damage if allowed

to remain on porcelain surfaces.

Lighting a Burner

• To avoid the chance of fire, explosion or carbon

monoxide poisoning, do not attempt to use your

cooktop without the burners completely and properly

assembled (see page 5). The burner rings spread the

flame evenly around the burner cap. The burner rings

must be properly seated for proper burner lighting and

operation.

• In the interest of safety, always light the burner before

putting the cooking utensil on the grate. Turn the

burner knob to the OFF position before removing the

utensil. Always check the position of the control knobs

to make sure the cooktop is off when you are finished

cooking.

• Do not turn the knob farther than the HIGH position

until lit. Doing so may result in a burst of flame that

could cause burns or damage to the surrounding area.

• Do not touch any part of the burner while the igniter is

sparking. An electrical shock could result.

• Never light the burners with a match or other open

flame.

• Always check to make sure all control knobs are in the

OFF position when you are finished cooking.

• If the gas does not ignite after four seconds or if the

flame goes out and gas escapes when attempting to

light a burner, turn the knob to the OFF position. Open

a window and allow at least five minutes for the gas to

dissipate. Then, repeat the lighting procedure.

Each burner control knob has a small diagram

next to it

 

1. To light a burner, push in gently on the knob and

turn it counter-clockwise to the HIGH position.

The igniter will spark (click) repeatedly until the

gas ignites. The burner should light within four

seconds.

11

Installation Requirements

Installation Requirements

8

Cabinet/Countertop Dimensions (cont.)

Cutout tole1/16” -0 (+1.6 mm, 0) unless otherwise noted.

Gas and electrical connections

*UDWHGRHVQRWSURWUXGHLQDFWXDOXQLW

Gas connection and power cord may be

routed through bottom or back of chassis

Increase countertop and overhang

additional 2 1/2” (64 mm) Min. for

combustible rear wall above

countertop

Non-combustible

rear wall, rear of

mounting platform

‡

Gas/electrical utility cut-out in left rear corner of

mounting platform

203 mm X 152 mm,

if gas and electrical are routed through bottom

3/8” (13 mm)

countertop overhang

½” (13 mm)

countertop

overhang

598 mm

11 7/16”

(291 mm)

‡

'ULOOWZR

 

 

/

 

” di

DPHWHUKROHV

LQWRIURQWRIEDVH

FDELQHW,WVKRXOGDOORZEROWKHDG[LQFKORQJ

1

3

7

EROWVLQWRKROHV(QVXUHWKHFDELQHWKROHVDUHV\PPHWULFDO

ZLWKWKHDSSOLDQFH

bolt

KROHV

7KHDSSOLDQFHKDVWZRKROG

GRZQEROWKROHVEHQHDWKLWVIURQWHQG6OLGHWKH

EROWV

LQWR

DSSOLDQFH

KROHVDQGUHVWDSSOLDQFHRQEDVHSODWIRUPVHFXUH

E

ROWVZLWKEROWQXWVXQGHUQHDWKPRXQWLQJSODWIRUP

1” thick mounting platform Min.

Cabinet face

below countertop

overhang

2” (51 mm)

1” (25 mm)

Cabinet/Countertop Cutout Dimensions - Top View

Please wait to obtain appliance prior to cutting dimensions.

10” (254 mm) min.

to combustible wall

above countertop,

both sides

Not actual position

of gas/electric

Summary of Contents for S9 6











Reviews: