background image

8

 9

PRE-INSTALLATION PROCEDURES

Ducted Mode

Recirculating Mode

(Fig. 1) Knob Settings

Ducted Mode

: Turn the knob 

to this 

setting for Ducted Installation.

 

Recirculating Mode

: Turn the knob 

to this setting for a Recirulating 

Installation.

 

• Please read the instructions carefully. Unpack the Range Hood and check that all

functions are working before installing. 

• Ensure that the voltage (V) and the frequency (Hz) indicated on the sticker match the

voltage and frequency at the installation site. 

• Check that the area behind the installation surface to be drilled is clear of any electrical

cables or pipes, etc. 

• The stainless steel surfaces of the Range Hood are very easily damaged during

installation if scratched or bumped by tools. Please take care to protect the surfaces 

during installation. 

• Protect the cooktop surface below with cardboard, or the like, to prevent damage

occurring during installation.

• The manufacturer shall not be held liable for failure to observe all safety regulations.

You will need to set the Range Hood mode to either Ducted or Recirculating.

1. Remove Aluminum Filters

2. Locate Knob Settings 

located under the

 Motor 

(Fig. 1)

3. Unlock the Settings Knob by unscrewing and setting to Ducted or Recirculating mode.

4. Lock the Knob into place by replacing the screw from 

Step 3

.

IMPORTANT READ BEFORE INSTALLATION 

INSTALLATION INSTRUCTIONS

Cabinet Installation Method

1.

2.

Use the 4 screws to mount the Range Hood to the

cabinet. Check that your mounting screws are in

the correct place by temporarily fitting the Range

in place. If correct

,

 lock into position by pushing in

the Range Hood.

130mm

2.75"

3.93"

7.08"

For 

Ducted

 installation drill a 130mm diameter hole 

into the cabinet and four 3.5mm diameter holes as 

pictured below picture.

For 

Ductless

 installation 

do not

 drill the 130mm 

diameter hole in the cabinet. Drill only the four 

3.5mm diamater holes as pictured below.

CAUTION:

 

HOOD

 

MAY

 

HAVE

 

VERY

 

SHARP

 

EDGES;

 

PLEASE

 

WEAR

 

PROTECTIVE

 

GLOVES

 

WHENEVER

 

IT

 

IS

 

NECESSARY

 

TO

 

REMOVE

 

ANY

 

PARTS

 

FOR

 

INSTALLING,

 

CLEANING

 

OR

 

SERVICING.

Summary of Contents for 5MU Series











Reviews: