Cosen SH-1000F Instruction Manual Download Page 80

Page: 80 / 104

9-12

#20. Broken Band Shows A Twist In Band Length

Probable Cause :

Excessive band tension

Any of the band conditions which cause the band to

be long (#18) or short (#19) on tooth edge.

Cutting a tight radius.

RE-ADJUSTING THE ROLLER TABLE

If the feeding table suffers the huge stroke and the alignment is effected, follow the below procedure

to adjust.

TOOL, measuring

Measurement, Horizontal balance

Procedure

Screw or loosen the adjusting bolt to attain the horizontal balance (leveling) between the roller

table and the machine frame.

Ensure that the machine frame is not struck by the loaded material on the feeding table.

Check the leveling by the measuring tool.

After finished the adjusting, fix the roller table.

If the feeding table and the machine frame are not positioned under the horizontal balance,

the loaded material may be going up gradually and affect the cutting effect.

Summary of Contents for SH-1000F









































































































Search results

Summary of Contents for SH-1000F

Reviews:

Related manuals for SH-1000F

Brands by name

Popular brands

Cosen SH-1000F, Instruction Manual

Search results

Summary of Contents for SH-1000F

Reviews:

Related manuals for SH-1000F

Brands by name

Popular brands