Cortelco 2194**VOE27S Owner'S Instruction Manual Download Page 25 | Manualshive

Page: 25 / 28

Cortelco 2194**VOE27S Owner'S Instruction Manual Download Page 25

FCC I

NFORMATION

DESIGN COMPLIANCE

Your telephone is designed to comply with FCC Rules and

Regulations, Part 68. It can be connected to the telephone network as FCC-registered
terminal equipment. The registration number is printed on the label on the bottom of your
telephone.

NOTIFICATION TO THE TELEPHONE COMPANY

As a customer of the local Telephone

company, you must, if they ask, tell them before connecting your telephone to the
telephone company lines. The telephone company may need the FCC registration
number and the ringer equivalence of the telephone. This information is printed on a label
on the bottom of your telephone.

RINGER EQUIVALENCE

The ringer equivalence indicates the amount of power that

your telephone draws from the telephone company line during ringing. The number is
printed on the label on the bottom of your telephone.

If you have more than one telephone (or other terminal device) connected to the
telephone company line, you should total the ringer equivalence numbers (REN s), and
be sure that the total is not more than five. Your telephones may not ring if the total is
more than five. Also, in some rural locations, your telephone may not ring if the REN total
is more than three.

RESTRICTIONS

You must not connect your telephone to coin-operated lines or party

lines.

INTERFERENCE POTENTIAL

Your telephone has a push-button dial that generates

radio frequency energy. If not properly used, it may interfere with radio and television
reception. If the telephone does cause interference with reception, move the radio or
television to another electrical circuit or another location. If necessary, you may need to
seek advice from an experienced technician.

INSTALLATION

This model telephone must be connected to the telephone company

lines through a modular jack. The required USOC for the modular jack is RJ11C for desk
mounting and RJ11W for wall mounting. The USOC number is printed on the label on the
bottom of your telephone.

TYPE OF DIALING

Your telephone has a push-button TONE dial. You must have TONE

service from your telephone company to use your telephone for dialing. Note that you
will usually be charged extra for TONE service. If you do not have Tone service, you
may use Pulse dialing.

HEARING-AID COMPATIBILITY

The handset on your telephone will work with mag-

netically-coupled hearing aids. You can use a hearing aid equipped with a T (Telephone)
switch.

IN CASE OF TROUBLE

If your telephone should cause problems on the telephone line,

the telephone company can temporarily disconnect your service. The telephone com-
pany must then notify and allow you to correct the problem.

The telephone company may from time to time change its lines or equipment. They
must notify you if planned changes will affect your telephone service, to allow you to
take steps to prevent interruptions.

22

«
...
23
24
25
26
27
...
»

Summary of Contents for 2194**VOE27S





























Reviews:

No comments