CORRECT CRAFT ski nautique 200cg Owner'S Manual Download

Page: 171 / 214

8-5

Care and Maintenance

Cartridge Replacement

1. Turn off power to the bilge pump.
2. Unscrew the filter bowl

(A)

turning counterclockwise and pour
any excess bilge water remaining in
the bowl back into the bilge.

3. Remove the used cartridge

(B)

and

dispose of in a suitable container.

4. Inspect the O-ring

(C)

located on

top of the bowl and replace if worn.

5. Be sure that the seals located on the

top and bottom of new cartridge are
in place and correctly aligned.

6. Place the new cartridge into the

bowl and reattach the bowl to the
filter housing

(D)

by turning

clockwise.

7.  Turn on power to the bilge pump.
8.  Turn on the bilge pump and inspect all connections for leaks.
9.  Bleed any air trapped in the housing by using the bleed button

(F)

or, if so equipped, the bleed screw

(E)

. Both are located on

top of the filter housing.

CORC0241

Summary of Contents for ski nautique 200cg























































































































































































































Search results

Summary of Contents for ski nautique 200cg

Reviews:

Related manuals for ski nautique 200cg

Brands by name

Popular brands

CORRECT CRAFT ski nautique 200cg, Owner'S Manual

Search results

Summary of Contents for ski nautique 200cg

Reviews:

Related manuals for ski nautique 200cg

Brands by name

Popular brands