manualshive.com logo in svg

coov N100 Pro, Function Instruction Manual, Page: 23 / 37

Share
Download
coov N100 Pro Function Instruction Manual Download Page 23

1.

校准：

1. Calibration:

A. 同时按下 HOME 键 + 中右键并松开，进入校准配置模式

A. Press the HOME+ Middle right button at the same time and release to enter the

calibration configuration mode.

B. 尝试转动两个摇杆，直到手柄停止震动

B. Try to turn the two rockers until the handle stops vibration

C. 停止震动后，先松开两个摇杆，再按一下 home 键

C. After the vibration is stopped, release the two rockers and press the HOME

button.

D. 等待 1 秒后，自动退出校准模式，转换器亮绿灯表示校准成功，红灯表示校准失败

D. Wait for 1 second, and it will exit the calibration mode automatically. The green

light of the converter indicates the success of calibration, and the red light indicates

the failure of calibration

2.

清除校准信息：

2. Elimination of calibration information:

A. 同时按下 HOME 键 + 中右键并松开，进入校准配置模式

A. Press the HOME+ Middle right button at the same time and release to enter the

calibration configuration mode.

B. 按下 Home 键并保持 3 秒，会清除所有校准参数，并退出配置模式

B. Hold down the HOME button for 3 seconds, all the calibration parameters will be

Summary of Contents for N100 Pro






































Reviews:

No comments