2 pcs
8 pcs
114"
42 pcs
1
3
4"
1"
8 pcs
212"
SWING
SEAT
BACK LEFT
BASE
LEFT END
BASE
17
UPPER RIGHT
REAR SUPPORT
1
2
3
x4
UPPER
FRAME SIDES
4
x2
TOP
FRAME PERCH
5
BACK LEFT
CENTER FRAME
SUPPORT
6
UPPER LEFT
TOP FRAME
SUPPORT
7
FRONT LEFT
BOTTOM FRAME
SUPPORT
8
x2
CENTER
BOTTOM FRAME
SUPPORT
9
LEFT FRONT
BOTTOM SUPPORT
10
x2
CENTER
TOP SUPPORT
11
LEFT DECK
FRAME
12
FRONT DECK
SUPPORT
13
CENTER DECK
SUPPORT
x2
14
RIGHT END
BASE
15
BACK RIGHT
BASE
16
BACK RIGHT
CENTER SUPPORT
18
FRONT RIGHT
BOTTOM FRAME
SUPPORT
19
RIGHT FRONT
CENTER SUPPORT
20
RIGHT DECK
FRAME
21
SWING
SIDE
x4
22
x2
25
HANGING TREAT
BASKET
24
LADDER
x2
23
DECK PLATFORM
A
A
A
A
A
B
A
A
A
.
.
.
.
.
.
39
A
x8
B
x1
1
2
3
4
5
6
3
A
B
C
D
E
F
1
2"
1 pcs
4 pcs
4 pcs
G
DON’T BUILD THIS IN YOUR KITCHEN! IT WON’T FIT THROUGH THE
DOOR. SINCE THE CHICKEN PLAY ACTIVITY CENTER IS LARGE ONCE
CONSTRUCTED, WE SUGGEST YOU BUILD EITHER OUTSIDE OR IN YOUR
GARAGE OR BARN.
IDENTIFY ALL PARTS AND HARDWARE THAT ARE INCLUDED WITH YOUR
ACTIVITY CENTER. GRAB A SCREWDRIVER (OR HAND DRILL), A RUBBER
MALLET AND IF YOU HAVE A CLAMP, IT WOULD BE HANDY. FIND A LEVEL
PLACE TO BUILD IT AND AN EXTRA SET OF HANDS WOULD ALWAYS BE
HELPFUL. START BUILDING!
YOU ARE GOING TO BUILD THIS ACTIVITY CENTER IN SECTIONS AND WILL BE STARTING WITH THE LEFT SIDE. GET PARTS #1-#6 AND SET THEM
AS THE IMAGE SHOWS. MATCH UP NOTCHES BEFORE INSERTING ANY OF THE PIECES TOGETHER.BEING THIS IS THE
BASE
OF THE UNIT, THESE
PIECES ARE GOING TO FIT VERY SNUG, SO ENSURING IT IS SET SQUARE AND GENTLY USING A RUBBER MALLET MIGHTHELP.
A.
PLACE #1 LEFT END BASE WITH THE TWO NOTCHES CLOSER TO THE GROUND FLAT AND INSERT #2 BACK LEFT BASE
(NOTCH FACING FORWARD AND CLOSE THE GROUND) INTO #1 WITH THE TONGUE AND GROVE TOWARDS THE
BACK. INSERT TWO #A SCREWS THROUGH PRE-DRILLED HOLES AND SECURE.
B.
ALIGN ONE #3 UPPER FRAME SIDE ON THE BACKSIDE OF #2 AND SECURE WITH ONE #A SCREW ON THE
BACK AND ONE #A ON THE SIDE. REPEAT WITH SECOND #3 UPPER FRAME SIDE BEHIND THE CENTER
NOTCH ON #1 AND SECURE WITH ONE #A SCREW. (NOTE-THE OTHER TWO #3 UPPER FRAME SIDES AND
ONE #4 TOP FRAME PERCH WILL BE USED ON THE OPPOSITE SIDE OF THE CENTER-SO SET THOSE ASIDE
FOR NOW.)
C.
REST #4 TOP FRAME ON TOP OF #3 SUPPORTS AND SECURE ONE #A SCREWS ON EACH SIDE THROUGH
TOP PRE-DRILLED HOLES.
D.
SECURE #5 BACK LEFT CENTER FRAME SUPPORT ON TOP FAR RIGHT OF #2. ENSURE THE PREDRILLED
HOLES ARE LEFT SIDE FACING.
E.
TAKE #6 UPPER LEFT REAR SUPPORT AND INSERT TONGUE/GROOVE END INTO #3 WITH NOTCH
FACING FORWARD. SECURE #6 INTO #5 THROUGH THE PRE-DRILLED HOLE IN THE BACK USING ONE #B
SCREW. THEN SECURE WITH ONE SCREW #A THROUGH THE PRE-DRILLED HOLE ON #3.
ASSEMBLY INSTRUCTIONS
Chicken Play Center Large
Model# 250-72
2
1
