Symbols on the machine
For safe operation and maintenance, symbols are carved in relief on the
machine. According to these indications, please be careful not to make any
mistake.
The port to refuel the “petrol/oil mix”.
Position: Air cleaner cover
The direction to close the choke.
Position: Air cleaner cover
The direction to open the choke.
Position: Air cleaner cover
Warning labels on the machine
Warning
!
Important
!
1) Read owner's thes instructions before
operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) Keep all children, bystanders and helpers
15 metres away from the machine.
If the warning label peels off or becomes soiled and
impossible to read, you should contact the dealer
from which you purchased the product to order new
labels and affix them in the required location(s).
Never modify your machine.
Warning labels and symbols on the machine
5
USING THE PRODUCT
IMPORTANT
Cut only materials recommended by the
manufacturer. And use only for tasks explained in
the manual.
1. Grip the handles firmly with both hands using
your whole hand. Place your feet slightly apart
(slightly further apart than the width of your
shoulders) so that your weight is distributed
evenly across both legs, and always be sure to
maintain a steady, even posture while working.
2. Maintain the speed of the engine at the level
required to perform cutting work, and never
raise the speed of the engine above the level
necessary.
3. If the unit starts to shake or vibrate, turn off the
engine and check the whole unit. Do not use it
until the trouble has been properly corrected.
4. Keep all parts of your body away from rotating
cutting attachment and hot surfaces.
5. Never touch the muffler, spark plug, or other
metallic parts of the engine while the engine is
in operation or immediately after shutting down
the engine. Doing so could result in serious
burns or electrical shock.
!
Operation
WARNING
Engine exhaust is hot and contains Carbon
Monoxide (CO), a poison gas. Breathing CO can
cause unconsciousness, serious injury or death.
Exhaust can cause serious burns. ALWAYS position
the machine so that exhaust is directed away from
your face and body.
COLD START ENGINE
1. Feed fuel into the fuel tank and tighten the cap
securely.
2. Push the fuel pump primer 10 times until
overflown fuels flows out in to the clear tube.
3. Position the choke lever to the closed position.
4. Position the throttle lever to the ‘Min’ position.
5. With one hand on the engine head and the other
gripping the pull start lever firmly grasp the start
cord lever and pull rapidly until the engine starts.
6. After the engine starts move the choke lever to
the open position.
7. Please Note: never allow the starter cable to
snap back as this may cause damage to the
machine.
WARM ENGINE START
1. The starting procedure is the same as the COLD
ENGINE START except DO NOT close the choke
lever.
STOPPING THE ENGINE
1. Move the throttle trigger to the MIN position and
allow the engine to return to an idling speed
before shutting the engine off.
2. Press and hold the stop button until the engine
has come to a complete stop.
3. If engine does not stop when the stop button is
pressed, close the choke to stall the engine.
WARNING
The blade or trimmer must not move at idle speed,
otherwise serious personal injury may/will occur.
Periodic carburettor adjustments may be required to
recalibrate the blade or trimmer heads do not move
when idle. If the blade or trimmer head move,
adjust the carburettor according to “Carburettor
Adjustment “instructions in this manual.
MAINTANENCE
WARNING
Moving parts can amputate fingers or cause severe
injuries. Keep hands, clothing and loose objects
away from all openings. Always stop the engine,
disconnect the spark plug, and make sure all
moving parts have come to a complete stop before
removing any obstructions, clearing debris, or
servicing the machine. Allow the machine to cool
before performing any service. Wear gloves to
protect your hands from sharp edges and hot
surfaces.
12